Din handlekurv er tom.

Handlekurv

Hjelp og kontakt

Gratis frakt over kr 3000

100-dagers returrett

Nyhetsbrev

Salg

Over 300 000 kunder - vi takker dere!

4,93/5 "Veldig bra" (1400+ anmeldelser)

40 000+ produkter for jakt og skytesport

SINCLAIR INTERNATIONAL
NECK TURNING CASEHOLDERS

749002490

The Sinclair Driver and Caseholder system is designed to hold and turn your case while you are neck turning, cleaning case necks or case mouth deburring. The caseholders and driver are machined from stainless steel, and the driver has a ¼" hex shaft for use in power screwdrivers or low speed drill motors. The driver is universal to the Sinclair system and will work with all the caseholders. Our Universal Caseholder enables you to use this system with our Sinclair Stainless Shell Holders listed on page 29. Select the appropriate shell holders for your favorite cartridges.. The Universal Caseholder works with the same #05-200 driver as our original caseholders, and it is available as a “kit” with the Driver and Universal Caseholder or individually for those who already have a driver. Remember to order the Sinclair Stainless Shell Holders for your Universal Caseholder if you don’t already have them. This system is a great, inexpensive way to speed up the neck turning process. Also works great for many other case prep operations.**NOTE: When ordering case holders, you will need to order a case holder driver as they are sold separately.**

Mer...

Sinclair Driver and Caseholder-systemet er designet for å holde og snu saken mens du er i nakken, rengjør saksen eller avluser munnen. Saksholderne og driveren er maskinert i rustfritt stål, og føreren har en ¼ "sekskantet aksel for bruk i kraftskrutrekkere eller lavhastighetsboremotorer. Driveren er universal for Sinclair-systemet og vil fungere med alle saksholdere. Vår Universal Caseholder muliggjør du skal bruke dette systemet med våre Sinclair Stainless Shell Holders oppført på side 29. Velg passende skallholdere for favorittpatronene dine. Universal Caseholder fungerer med den samme # 05-200 driveren som våre opprinnelige saksholdere, og den er tilgjengelig som en "Kit" med Driver og Universal Caseholder eller individuelt for de som allerede har en driver. Husk å bestille Sinclair Stainless Shell Holders til Universal Caseholder hvis du ikke allerede har dem. Dette systemet er en flott og billig måte å hastighet på opp i nakken vri prosessen. Fungerer også bra for mange andre saksforberedende operasjoner. ** MERK: Når du bestiller saksinnehavere, må du bestille en saksbehandler når de selges separat y. **

Mer...

Kundevurderinger for SINCLAIR INTERNATIONAL #4 BELTED MAGNUM FAMILY NECK TURNING CASEHOLDER

Antall vurderinger: 8
Fra brownells.com: 8
Gjennomsnittsvurdering: 4,5

Excellent Time saver (13.03.2011)

This is a must have if you get the neck turning tools. It not only makes the job faster but you get a much smoother finish on your brass. Don't forget to get the Lee autoprime shell holders kit for it as well.

Can't clean entire length of case (28.03.2011)

For cleaning cases with #0000 steel wool, this tool leaves a strip of powder residue around the bottom of the case. That's because the Lee Shell Holder is held inside (and below) the top of the universal holder. I prefer the Sinclair Driver Style Caseholders because they hold the case further out so my steel wool can reach the entire outside of the case.

This thing is Great!! (17.05.2011)

This is an easy way to turn case necks with a cordless drill.

Outside of case not fully accessable (20.07.2011)

I like to clean powder residue from my cases by chucking them up in my hand drill and using #0000 steel wool. Since the Lee Shell Holder is held inside (and below) the top of this Universal Holder, I can't reach all the way down the side of the case. A strip of residue is left above the case head. I prefer the Sinclair Driver Style Case Holders because they expose the entire length of the case. My steel wool can then reach all the way down the side of the case.

Super tool! (18.05.2012)

I like my brass to look as good as it performs and this tool helps me to polish my cartridges. I place a cartridge into the caseholder and the driver into my cordless screwdriver. I then take some scotch bright and hold it around the case and turn on the screwdriver. In just seconds the case shines better than new!

Awesome product (09.01.2013)

I have been using a hand neck turner and caseholder and decided to try this item. What a great little tool! I use it with a battery powered mini-screwdriver and my Dewalt shop drill. With either one, my necks turn out more consistent and smoother than hand turning those necks. Takes half the time too.

The unit is well made and robust. The drill bit holder is a screw on the other end of it that screws into the caseholder proper. The end of this screw is rounded. This rounded end fits into the primer pocket hole,and presses against it. This aligns the case and holds it securely.

When used with a hand neck turner the case will usually wobble about a bit as the drill turns but as long as the mandrel on the neck turner is a snug fit inside the case neck, the neck turns out consistent and smooth. ( I check the concentricity with a case neck gauge)

Not often you run into a product that can described as "perfect" but this is as close as you can get. Highly recommend it.

Superior to Sinclair's other caseholder. (28.03.2011)

For cleaning cases with #0000 steel wool, this tool is better than the other Sinclair tool which uses Lee shell holders. This tool exposes the entire outside of the case so your steel wool can reach all of the powder residue.

GREAT TOOL! (23.11.2011)

WAY TO GO FOR NECK TURNING

Les 8 flere anmeldelser fra brownells.com

299 399 9 NOK

Produktnr.: 749002490
SINCLAIR INTERNATIONAL #4 BELTED MAGNUM FAMILY NECK TURNING CASEHOLDER
Produsentnr.: 05240 Sinclair Driver and Caseholder-systemet er designet for å holde og snu saken mens du er i nakken, rengjør saksen eller avluser munnen. Saksholderne og driveren er maskinert i rustfritt stål, og føreren har en ¼ "sekskantet aksel for bruk i kraftskrutrekkere eller lavhastighetsboremotorer. Driveren er universal for Sinclair-systemet og vil fungere med alle saksholdere. Vår Universal Caseholder muliggjør du skal bruke dette systemet med våre Sinclair Stainless Shell Holders oppført på side 29. Velg passende skallholdere for favorittpatronene dine. Universal Caseholder fungerer med den samme # 05-200 driveren som våre opprinnelige saksholdere, og den er tilgjengelig som en "Kit" med Driver og Universal Caseholder eller individuelt for de som allerede har en driver. Husk å bestille Sinclair Stainless Shell Holders til Universal Caseholder hvis du ikke allerede har dem. Dette systemet er en flott og billig måte å hastighet på opp i nakken vri prosessen. Fungerer også bra for mange andre saksforberedende operasjoner. ** MERK: Når du bestiller saksinnehavere, må du bestille en saksbehandler når de selges separat y. **

399 NOK 5 kr 399,00 *

Leveringstid ca. 14-21 dager.
5 stk. på lageret i USA

Spesifikasjoner: Kaliber: 300 Winchester Magnum, 300 H&H Magnum, 300 Weatherby Magnum, 257 Weatherby Magnum, 270 Weatherby Magnum, 340 Weatherby Magnum, 338 Ruger Compact Magnum, 300 Ruger Compact Magnum, 264 Winchester Magnum, 300 PRC, 350

SINCLAIR INTERNATIONAL NECK TURNING CASEHOLDERS

Kundevurderinger for SINCLAIR INTERNATIONAL #4 BELTED MAGNUM FAMILY NECK TURNING CASEHOLDER

Top takeaways

Attributes

Elementdetaljer

Kundevurderinger for SINCLAIR INTERNATIONAL #4 BELTED MAGNUM FAMILY NECK TURNING CASEHOLDER

Koble til

Sikre betalingsmåter

Bransjeorganisasjoner

Velkommen!

SINCLAIR INTERNATIONAL
NECK TURNING CASEHOLDERS