CORE RIFLE SYSTEMS
AR-15/M16 BILLET CHARGING HANDLES

608938410832 100012332

Machined Billet Charging Handle Gives Strength & Consistent Tolerances

Machined from a solid aluminum billet, charging handle drops in to standard AR-15/M16 uppers to offer exceptional strength and extremely consistent tolerances. Hardcoat anodized to resist wear and corrosion.

SPECS: Machined billet 6061 T6 aluminum, hardcoat anodized matte black. 6 7/8"(17.5cm) long. V1 latch .56" (1.4cm) long.

Mer...

Maskinert Billet Ladespak Gir Styrke & Konsistente Toleranser

Maskinert fra en solid aluminiumsbillet, ladespak faller inn i standard AR-15/M16 overdel for å tilby eksepsjonell styrke og ekstremt konsistente toleranser. Hardcoat anodisert for å motstå slitasje og korrosjon.

SPECS: Maskinert billet 6061 T6 aluminium, hardcoat anodisert matt svart. 6 7/8"(17.5cm) lang. V1-lås .56" (1.4cm) lang.

Mer...

Kundevurderinger for CORE RIFLE SYSTEMS BILLET CHARGING HANDLE

Antall vurderinger: 7
Fra brownells.com: 7
Gjennomsnittsvurdering: 2,9

I have purchased several quality product (19.11.2016)

Not Within Specs (23.02.2014)

This charging handle is not in specs. Installed the part and it drags and snags in a few places. Pulled the charging handle to the rear maybe 10 times and the aluminum is already showing through on top of the charging handle as well as underneath to the read of the charging handle. I tried two other charging handles including a stock one that came with another AR and a BCM Gunfighter and neither had any problems in the upper.

Good quality changing handle for the mon (03.11.2016)

I noticed an old negative review on this product. I have used Core changing handles for quite a while on my custom builds. Good product no problems. Their extended model is a good value and I am purchasing a few more.

Didn't fit (16.11.2013)

The product quality and finish looked fine. However, the charging handle didn't fit in 2 out my 3 uppers. I bought it for use in a Stag Lefty upper as part of a build I'm doing for my wife. It didn't fit in there, so I tried swapping it out with one from my 20" Del Ton, where it also did not fit. I ended up swapping the charging handle from my LWRC M6A2, and it seems to work in there. Other than the fit issues, the handle appears to be well made. It didn't appear bent or otherwise compromised. I don't know if the bolt key channels in those particular uppers are a bit tight or what, but I made it work by shifting parts around, though I would have preferred to keep parts where they were, because I know they worked the way they were. I doubt this charging handle will compromise the reliabilty of the LWRC, but if it does, I'll use it to weigh my garbage can down.

Good Quality Charging Handle (16.12.2013)

Fits Perfecly In My Delton Receiver..Good Quality And The Finish Is Perfect..Best Of All Made In The USA...

Rough (21.04.2014)

The anodized finish is rough. The latch has a sharp edge that does not easily engage the upper. The latch spring is stronger than it needs to be. The latch does not easily disengage when pulling the charging handle back. I returned this charging handle.

Core Billet Charging Handle (02.07.2015)

This is by far the worst changing handle I have ever purchased. I will return for a full refund the quality is just not there. The charging handle was poorly machined rough and as sharp as you can get.

Les 7 flere anmeldelser fra brownells.com

0 0 1 NOK

Produktnr.: 100012332
CORE RIFLE SYSTEMS BILLET CHARGING HANDLE
Produsentnr.: 1856 608938410832 Maskinert fra en solid aluminiumsbillet, ladespak faller inn i standard AR-15/M16 overdel for å tilby eksepsjonell styrke og ekstremt konsistente toleranser. Hardcoat anodisert for å motstå slitasje og korrosjon.

Varsle ved tilgjengelighet

Ikke tilgjengelig.

Spesifikasjoner: Finish: Black Hand: Right Make: AR-15

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Attributes

Finish: Black Hand: Right Make: AR-15 Leveringsvekt: 0,045kg Frakthøyde: 13mm Fraktbredde: 76mm Fraktlengde: 218mm UPC : 608938410832