Roller-Guided Stoning For Precise Sear Engagement Cuts
Aluminum jig uses two rollers to guide your stone evenly over the sear to let you get the exact angle for a crisp, clean trigger pull. Three modes allow you to pre-set, mate, and set up for secondary stoning to ensure that the hammer-sear engagement is precisely set. An adjustable angle mode is also available for experimenting with different angles. Brass rollers prevent over-stoning the sear and an adjustable insert and knob work with the sear block to lock the sear in place to prevent movement.
SPECS: Aluminum block, brass rollers. Includes instructions.
Mer...
Rullestyrt Slipning For Presis Sear-Engasjement Kutt
Aluminiumsjiggen bruker to ruller for å føre slipesteinen jevnt over searen slik at du kan få den eksakte vinkelen for en skarp og ren avtrekker. Tre moduser lar deg forhåndsinnstille, tilpasse og stille inn for sekundær sliping for å sikre at hammer-sear-engasjementet er nøyaktig satt. En justerbar vinkelmodus er også tilgjengelig for eksperimentering med forskjellige vinkler. Messingrullene forhindrer over-sliping av searen og en justerbar innsats og knott arbeider sammen med searblokken for å låse searen på plass og forhindre bevegelse.
Kundevurderinger for MARVEL PRECISION ULTIMATE 1911 SEAR JIG
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 4
Worked Moderate(21.10.2010)
Ok let me start by saying i am new to gunsmithing, more a hobby than any thing. BUT here is my review on this item
The problems i had is the wingnut on the back side of this photo that holds the block high adjustment in place puts the block in to a slight angle when tightened, Not sure it is enough to make a difference. But when you tighten that nut it does tend to lift the bock up and change the cut height of the sear.
kind of a pita
I think the idea is good but the mfg of the item leaves me a little cold.
Best on the Market(05.08.2011)
Easy to set up and use. Easy to understand instructions. Better than any other jig I have tried.
Produktnr.: 588000003 MARVEL PRECISION ULTIMATE 1911 SEAR JIG Produsentnr.: NONE Aluminiumsjiggen bruker to ruller for å føre slipesteinen jevnt over searen slik at du kan få den eksakte vinkelen for en skarp og ren avtrekker. Tre moduser lar deg forhåndsinnstille, tilpasse og stille inn for sekundær sliping for å sikre at hammer-sear-engasjementet er nøyaktig satt. En justerbar vinkelmodus er også tilgjengelig for eksperimentering med forskjellige vinkler. Messingrullene forhindrer over-sliping av searen og en justerbar innsats og knott arbeider sammen med searblokken for å låse searen på plass og forhindre bevegelse.
3849NOK5kr 3 849,00
*
Leveringstid ca. 14-21 dager. 5 stk. på lageret i USA
Roller-Guided Stoning For Precise Sear Engagement Cuts
Aluminum jig uses two rollers to guide your stone evenly over the sear to let you get the exact angle for a crisp, clean trigger pull. Three modes allow you to pre-set, mate, and set up for secondary stoning to ensure that the hammer-sear engagement is precisely set. An adjustable angle mode is also available for experimenting with different angles. Brass rollers prevent over-stoning the sear and an adjustable insert and knob work with the sear block to lock the sear in place to prevent movement.
SPECS: Aluminum block, brass rollers. Includes instructions.
Mer...
Rullestyrt Slipning For Presis Sear-Engasjement Kutt
Aluminiumsjiggen bruker to ruller for å føre slipesteinen jevnt over searen slik at du kan få den eksakte vinkelen for en skarp og ren avtrekker. Tre moduser lar deg forhåndsinnstille, tilpasse og stille inn for sekundær sliping for å sikre at hammer-sear-engasjementet er nøyaktig satt. En justerbar vinkelmodus er også tilgjengelig for eksperimentering med forskjellige vinkler. Messingrullene forhindrer over-sliping av searen og en justerbar innsats og knott arbeider sammen med searblokken for å låse searen på plass og forhindre bevegelse.
Kundevurderinger for MARVEL PRECISION ULTIMATE 1911 SEAR JIG
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 4
Worked Moderate(21.10.2010)
Ok let me start by saying i am new to gunsmithing, more a hobby than any thing. BUT here is my review on this item
The problems i had is the wingnut on the back side of this photo that holds the block high adjustment in place puts the block in to a slight angle when tightened, Not sure it is enough to make a difference. But when you tighten that nut it does tend to lift the bock up and change the cut height of the sear.
kind of a pita
I think the idea is good but the mfg of the item leaves me a little cold.
Best on the Market(05.08.2011)
Easy to set up and use. Easy to understand instructions. Better than any other jig I have tried.