One-piece, MIL-STD 1913 Picatinny rail allows mounting a variety of optics and tactical sights on popular Mossberg, Remington, and Benelli shotguns. Streamlined, low profile design installs to the top of the receiver for a smooth “built-in” appearance. Four slotted flat head screws and washers secure rail to receiver for exceptional holding power. Precision machined from 6061-T6 aluminum, then mil-spec Type III hardcoat anodized for added strength. Fits shotguns with factory drilled and tapped receivers or receivers custom that require drilling and tapping for appropriate threads.
SPECS: 6061 T6 aluminum, Type III hardcoat anodized, matte black. Fits factory drilled and tapped receivers. Includes mounting hardware and instructions. Mossberg – 5½" (13.9cm) long. Fits 1997 and later-mfr pump action shotguns; can be installed on 930 semi-auto with additional fitting. Benelli M2 - 4½" (11.4cm) long. Drop-in fit on M2 Tactical; can also be installed on round-top M1 after drilling and tapping receiver. Comes with 4 slotted flat head screws and 4 washers.
Mer...
Monter Optikk eller Taktiske Sikter
Ettstykket, MIL-STD 1913 Picatinny rail som muliggjør montering av et utvalg optikk og taktiske sikter på populære hagler fra Mossberg, Remington og Benelli. Strømlinjeformet, lavprofil design monteres på toppen av mottakeren for et glatt «innebygd» utseende. Fire sporkappede flathode skruer og skiver fester skinnen til mottakeren for eksepsjonell holdekraft. Presisjonsmaskinert fra 6061-T6 aluminium, deretter mil-spec Type III hardcoat anodisert for ekstra styrke. Passer hagler med fabrikkborede og gjengede mottakere eller mottakere som krever boring og gjenging for passende gjenger.
SPECS: 6061 T6 aluminium, Type III hardcoat anodisert, matt svart. Passer fabrikkborede og gjengede mottakere. Inkluderer monteringsutstyr og instruksjoner. Mossberg – 5½" (13.9cm) lang. Passer pumpehagler produsert 1997 og senere; kan installeres på 930 halvautomat med ekstra tilpasning. Benelli M2 - 4½" (11.4cm) lang. Passer direkte på M2 Tactical; kan også installeres på runde M1 etter boring og gjenging av mottaker. Leveres med 4 sporkappede flathode skruer og 4 skiver.
Mer...
Kundevurderinger for MESA TACTICAL PRODUCTS BENELLI M2 RECEIVER RAIL
Antall vurderinger: 5
Fra brownells.com: 5
Gjennomsnittsvurdering: 4,4
Nice Rail(02.10.2012)
This is a well made rail. It was a good match to the top of the Rem. 870 receiver. The only down-side was that it wasn't supplied with 8-40 hardware as advertised, but 6-48 screws. I had to spend a little more time hunting up the correct tap.
Mesa Tactical should also add a schematic that shows the hole spacing (center to center). This would save the gunsmith some time and eliminate one spot where he might make a mistake.
A good product at a good price.(25.08.2015)
Australian Border force that were Australian Customs and Border Security have commissioned me to put a receiver rail on some of their shotguns for them to assess their suitability as a tactical shotgun base for their shotguns.
I found that the front screw was a bit short and I had to deepen the front screw hole to ensure full engagement of the screw.
Other that that I am pleased with this product and am sure we will be ordering more in the near future.
We have to order under $100 US and that is inconvenient but that is the law.
Awesome Product(09.08.2017)
Had a Remington Wingmaster come into the shop to get Cerakote and have a rail installed on it. Went with this Mesa Tactical one caused it looked pretty well built. Got it in and was able to install it. It fit like a glove and the screws were all sized to length, even the one the goes over the barrel and bolt. All I had to do was drill and tap the holes. Great product.
Works as advertised(07.09.2009)
Not much to it, a rail and 4 screws. I bought this knowing I would have to tap the receiver of my 870 to mount it. The rail looks good on the receiver and holds my Aimpoint in place. The hardest part of the install was finding the tap (my snapon set didn't have it) and making sure that the rail is straight. It required fitting on my gun since it wasn't tapped from the factory. Overall, recommend.
Just what I needed(09.06.2010)
I used this rail for my Mossberg 590 and I didnt need to tap anything on my receiver. There were pre drilled holes already on the top of the receiver and they fit perfectly.
Produktnr.: 100005803 MESA TACTICAL PRODUCTS BENELLI M2 RECEIVER RAIL Produsentnr.: 92390878405001041 Ettstykket, MIL-STD 1913 Picatinny rail som muliggjør montering av et utvalg optikk og taktiske sikter på populære hagler fra Mossberg, Remington og Benelli. Strømlinjeformet, lavprofil design monteres på toppen av mottakeren for et glatt «innebygd» utseende. Fire sporkappede flathode skruer og skiver fester skinnen til mottakeren for eksepsjonell holdekraft. Presisjonsmaskinert fra 6061-T6 aluminium, deretter mil-spec Type III hardcoat anodisert for ekstra styrke. Passer hagler med fabrikkborede og gjengede mottakere eller mottakere som krever boring og gjenging for passende gjenger.
Produktnr.: 100004034 MESA TACTICAL PRODUCTS MOSSBERG 500 RECEIVER RAIL Produsentnr.: 90770400000089041 Ettstykket, MIL-STD 1913 Picatinny rail som muliggjør montering av et utvalg optikk og taktiske sikter på populære hagler fra Mossberg, Remington og Benelli. Strømlinjeformet, lavprofil design monteres på toppen av mottakeren for et glatt «innebygd» utseende. Fire sporkappede flathode skruer og skiver fester skinnen til mottakeren for eksepsjonell holdekraft. Presisjonsmaskinert fra 6061-T6 aluminium, deretter mil-spec Type III hardcoat anodisert for ekstra styrke. Passer hagler med fabrikkborede og gjengede mottakere eller mottakere som krever boring og gjenging for passende gjenger.
One-piece, MIL-STD 1913 Picatinny rail allows mounting a variety of optics and tactical sights on popular Mossberg, Remington, and Benelli shotguns. Streamlined, low profile design installs to the top of the receiver for a smooth “built-in” appearance. Four slotted flat head screws and washers secure rail to receiver for exceptional holding power. Precision machined from 6061-T6 aluminum, then mil-spec Type III hardcoat anodized for added strength. Fits shotguns with factory drilled and tapped receivers or receivers custom that require drilling and tapping for appropriate threads.
SPECS: 6061 T6 aluminum, Type III hardcoat anodized, matte black. Fits factory drilled and tapped receivers. Includes mounting hardware and instructions. Mossberg – 5½" (13.9cm) long. Fits 1997 and later-mfr pump action shotguns; can be installed on 930 semi-auto with additional fitting. Benelli M2 - 4½" (11.4cm) long. Drop-in fit on M2 Tactical; can also be installed on round-top M1 after drilling and tapping receiver. Comes with 4 slotted flat head screws and 4 washers.
Mer...
Monter Optikk eller Taktiske Sikter
Ettstykket, MIL-STD 1913 Picatinny rail som muliggjør montering av et utvalg optikk og taktiske sikter på populære hagler fra Mossberg, Remington og Benelli. Strømlinjeformet, lavprofil design monteres på toppen av mottakeren for et glatt «innebygd» utseende. Fire sporkappede flathode skruer og skiver fester skinnen til mottakeren for eksepsjonell holdekraft. Presisjonsmaskinert fra 6061-T6 aluminium, deretter mil-spec Type III hardcoat anodisert for ekstra styrke. Passer hagler med fabrikkborede og gjengede mottakere eller mottakere som krever boring og gjenging for passende gjenger.
SPECS: 6061 T6 aluminium, Type III hardcoat anodisert, matt svart. Passer fabrikkborede og gjengede mottakere. Inkluderer monteringsutstyr og instruksjoner. Mossberg – 5½" (13.9cm) lang. Passer pumpehagler produsert 1997 og senere; kan installeres på 930 halvautomat med ekstra tilpasning. Benelli M2 - 4½" (11.4cm) lang. Passer direkte på M2 Tactical; kan også installeres på runde M1 etter boring og gjenging av mottaker. Leveres med 4 sporkappede flathode skruer og 4 skiver.
Mer...
Kundevurderinger for MESA TACTICAL PRODUCTS BENELLI M2 RECEIVER RAIL
Antall vurderinger: 5
Fra brownells.com: 5
Gjennomsnittsvurdering: 4,4
Nice Rail(02.10.2012)
This is a well made rail. It was a good match to the top of the Rem. 870 receiver. The only down-side was that it wasn't supplied with 8-40 hardware as advertised, but 6-48 screws. I had to spend a little more time hunting up the correct tap.
Mesa Tactical should also add a schematic that shows the hole spacing (center to center). This would save the gunsmith some time and eliminate one spot where he might make a mistake.
A good product at a good price.(25.08.2015)
Australian Border force that were Australian Customs and Border Security have commissioned me to put a receiver rail on some of their shotguns for them to assess their suitability as a tactical shotgun base for their shotguns.
I found that the front screw was a bit short and I had to deepen the front screw hole to ensure full engagement of the screw.
Other that that I am pleased with this product and am sure we will be ordering more in the near future.
We have to order under $100 US and that is inconvenient but that is the law.
Awesome Product(09.08.2017)
Had a Remington Wingmaster come into the shop to get Cerakote and have a rail installed on it. Went with this Mesa Tactical one caused it looked pretty well built. Got it in and was able to install it. It fit like a glove and the screws were all sized to length, even the one the goes over the barrel and bolt. All I had to do was drill and tap the holes. Great product.
Works as advertised(07.09.2009)
Not much to it, a rail and 4 screws. I bought this knowing I would have to tap the receiver of my 870 to mount it. The rail looks good on the receiver and holds my Aimpoint in place. The hardest part of the install was finding the tap (my snapon set didn't have it) and making sure that the rail is straight. It required fitting on my gun since it wasn't tapped from the factory. Overall, recommend.
Just what I needed(09.06.2010)
I used this rail for my Mossberg 590 and I didnt need to tap anything on my receiver. There were pre drilled holes already on the top of the receiver and they fit perfectly.