Din handlekurv er tom.

Handlekurv

Hjelp og kontakt

Gratis frakt over kr 3000

100-dagers returrett

Nyhetsbrev

Salg

Over 300 000 kunder - vi takker dere!

4,93/5 "Veldig bra" (1400+ anmeldelser)

40 000+ produkter for jakt og skytesport

BROWNELLS
SHOTGUN BARREL POLISHING FLEX HONE®

050806018914 080605016

Puts Finish Polish On Shotgun Bores That Is Truly Outstanding

Hundreds of abrasive "balls" mounted on a flexible shaft - the fastest, easiest way we've come across to clean and polish older barrels or put a mirror polish in new ones. For used barrels, the Medium-Coarse hone, followed by the Fine, removes rough and tight spots and brings the bore to a bright finish that you can see and feel . . . just run a patch through it before and after; the difference is amazing! We found too, that we could feel tight spots during honing and spend extra time on them until they were evened out. On new barrels, the Fine hone by itself will bring the factory finish up to a beautiful, mirror-bright finish that's a real customer pleaser. Easy to use: chuck in a variable speed electric drill; wet the hone with Flex Hone® oil; start the drill and insert the hone into the barrel from the breech end (if possible). As it cuts, a slurry of abrasive and oil develops to help speed the cutting action. Flex Hone® available (shown below) in sets and individual hones for 10, 12, 16 and 20 gauge barrels as well as .410 bore. Also, special-sized hones for 10, 12, 16, 20 gauge chambers and .410 bore. Instructions walk you through the steps for a perfect job. (You MUST use Flex Hone® oil - all other oils will destroy the abrasive "balls" and void our guarantee!) 750 RPM MAX. Avoid excess pressure. View Flex-Hone PDF Here

SPECS: Flex Honefor Barrels; 10, 12, 16, 20 ga., .410 bore. 33" (83.8cm) long in Med.-Coarse grit (red tip) or Fine grit (light blue tip). Flex Hone for Chambers; 10, 12, 16, 20 ga., .410 bore 12" (6.5cm) long, fine grit (light blue only). Set includes Med.-Coarse & Fine barrel hones, Chamber hone & 1 qt. Flex Hone oil, for 1 ga.

Medium grit is 180 grit silicon carbide and Fine grit is 800 grit aluminum oxide.

Mer...

Gir Finish Polish På Hagleløp Som Er Virkelig Enestående

Hundrevis av slipende "baller" montert på en fleksibel aksel - den raskeste, enkleste måten vi har kommet over for å rengjøre og polere eldre løp eller gi nye løp en speilpolering. For brukte løp fjerner Med.-Coarse hone, etterfulgt av Fine, ru og trange områder og gir løpet en lys finish som du kan se og føle... bare kjør en fille gjennom det før og etter; forskjellen er fantastisk! Vi fant også ut at vi kunne føle trange områder under honing og bruke ekstra tid på dem til de var jevnet ut. På nye løp vil Fine hone alene bringe fabrikkfinishen opp til en vakker, speilblank finish som virkelig gleder kundene. Enkel å bruke: sett i en variabel hastighet elektrisk drill; våt honen med Flex Hone® olje; start drillen og sett inn honen i løpet fra kammerenden (om mulig). Når den kutter, utvikles en slurry av slipemiddel og olje for å hjelpe til med å akselerere kuttaksjonen. Flex Hone® tilgjengelig (vist nedenfor) i sett og individuelle hones for 10, 12, 16 og 20 gauge løp samt .410 bore. Også spesialstørrelser hones for 10, 12, 16, 20 gauge kammer og .410 bore. Instruksjoner leder deg gjennom trinnene for et perfekt resultat. (Du MÅ bruke Flex Hone® olje - alle andre oljer vil ødelegge de slipende "ballene" og oppheve vår garanti!) 750 RPM MAKS. Unngå overdreven press. Se Flex-Hone PDF Her

SPECS: Flex Hone for løp; 10, 12, 16, 20 ga., .410 bore. 33" (83.8cm) lang i Med.-Coarse grit (rødt tips) eller Fine grit (lys blått tips). Flex Hone for kammer; 10, 12, 16, 20 ga., .410 bore 12" (6.5cm) lang, fine grit (kun lys blå). Sett inkluderer Med.-Coarse & Fine løpshones, kammerhone & 1 qt. Flex Hone olje, for 1 ga.

Medium grit er 180 grit silisiumkarbid og Fine grit er 800 grit aluminiumoksid.

Mer...

Kundevurderinger for BROWNELLS 16 GAUGE FLEX HONE SET W/OIL

Antall vurderinger: 4
Fra brownells.com: 4
Gjennomsnittsvurdering: 4,5

Wow (03.05.2010)

All I can say is "Wow!" I purchased a new 870 "Tactical" with a choked 18.5" barrel. I used el-cheapo Winchester promo shells to break it in. I soon discovered that these shells have problems with many guns; sadly this 870 is no exception. The general consensus is that the chambers on susceptible guns are not polished well enough. My chamber looked fine to me but I figured I'd give this Flex-Hone a shot anyway. Not being able to shoot cheap ammo is not a good thing to me. Well, after I taped off the depth, soaked the brush with several sprays of silicon oil & chucked it up in the drill I got to work. 20 seconds later I was done. Hard work to be sure. I can't believe how smooth & shiny the chamber is now. My only anger at this point is that Remington didn't do this job before the gun left the factory. Seriously took me all of 10 min start to finish. A factory worker could do it in about 10-20 seconds. Come on! Polish the chamber already Remington.

too short (27.05.2011)

I figured the 12 inch would be long enough to handle this old 410 I was restoring for my grandson- but it wasn't- there remained a 3 inch section in the middle that I could not hone- It did a beautiful job on what I could reach but the center section well it didn't look too good. I had a bit extender but it was too large in diameter to get into the barrell. I ended up with a wirebrush with some steel wool on it and did a pretty good job- I would like to see an extension that would fit inside the barrell.

Great Product (04.03.2011)

This system slicks up a shotgun barrel in no time and it looks great. Good for polishing up old barrels or putting a custom touch on new guns. Easy to use with a good hand drill. The Flex Hone Oil can be messy so make appropriate preparations to work space.

Easy and effective. Highly recommended (12.01.2016)

I am upping my game this turkey season with a new Leupold shotgun scope on top of my Beretta A400 Extreme. New Rhino turkey choke, Nitro shells should be lethal. Buddy told me I should polish the bore and chamber to tighten up groups and add some lethality. He described an arduous hours long process with many steps. I did some research and found the Flex Hone system. Sounded too good to be true. Bought it because I trust Brownell's. Received it today. Kit contains both 400 and 800 grit bore rods, one 800 grit chamber rod and a quart of Flex Hone's cutting oil. I swear it took no more than 20 minutes to polish both chamber and bore to a mirror shine. If you want an ultra shiny bore, this is the product for you. Ten passes in and out is all it took. Don't overdo it as you might take off too much steel. Watch Flex Hone's video for instructions. I didn't wash it out with soapy water as they suggest, just dry patches until they were clean followed with a slightly oily one.

Les 4 flere anmeldelser fra brownells.com

899 3649 19 NOK

Produktnr.: 080605016
BROWNELLS 16 GAUGE FLEX HONE SET W/OIL 050806018914 Hundrevis av slipende "baller" montert på en fleksibel aksel - den raskeste, enkleste måten vi har kommet over for å rengjøre og polere eldre løp eller gi nye løp en speilpolering. For brukte løp fjerner Med.-Coarse hone, etterfulgt av Fine, ru og trange områder og gir løpet en lys finish som du kan se og føle... bare kjør en fille gjennom det før og etter; forskjellen er fantastisk! Vi fant også ut at vi kunne føle trange områder under honing og bruke ekstra tid på dem til de var jevnet ut. På nye løp vil Fine hone alene bringe fabrikkfinishen opp til en vakker, speilblank finish som virkelig gleder kundene. Enkel å bruke: sett i en variabel hastighet elektrisk drill; våt honen med Flex Hone® olje; start drillen og sett inn honen i løpet fra kammerenden (om mulig). Når den kutter, utvikles en slurry av slipemiddel og olje for å hjelpe til med å akselerere kuttaksjonen. Flex Hone® tilgjengelig (vist nedenfor) i sett og individuelle hones for 10, 12, 16 og 20 gauge løp samt .410 bore. Også spesialstørrelser hones for 10, 12, 16, 20 gauge kammer og .410 bore. Instruksjoner leder deg gjennom trinnene for et perfekt resultat. (Du MÅ bruke Flex Hone® olje - alle andre oljer vil ødelegge de slipende "ballene" og oppheve vår garanti!) 750 RPM MAKS. Unngå overdreven press. Se Flex-Hone PDF Her

3499 NOK 0 kr 3 499,00 *

Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.

Spesifikasjoner: Gauge: 16 Gauge Make: Universal Shotguns

BROWNELLS SHOTGUN BARREL POLISHING FLEX HONE®

Kundevurderinger for BROWNELLS 16 GAUGE FLEX HONE SET W/OIL

Top takeaways

Attributes

Elementdetaljer

Kundevurderinger for BROWNELLS 16 GAUGE FLEX HONE SET W/OIL

Koble til

Sikre betalingsmåter

Bransjeorganisasjoner

Velkommen!

BROWNELLS
SHOTGUN BARREL POLISHING FLEX HONE®