Din handlekurv er tom.

Handlekurv

Hjelp og kontakt

Gratis frakt over kr 3000

100-dagers returrett

Nyhetsbrev

Salg

Over 300 000 kunder - vi takker dere!

4,93/5 "Veldig bra" (1400+ anmeldelser)

40 000+ produkter for jakt og skytesport

VOLQUARTSEN
RUGER® MK II™ TL 2000 REAR SIGHT

810162011734 930000011

Precision Machined For Match Accuracy

All components are CNC milled from a solid steel billet to ensure accurate, repeatable click adjustments for windage and elevation. The serrated rear leaf features a slight reverse angle to reduce glare and improve sight picture. Fully compatible with the factory front sight on Mk I and Mk II™ pistols. Fits Ruger® 22 pistols equipped with factory adjustable rear sight. No fitting required, uses factory dovetail; locks in place with two set screws.

SPECS: Steel, blue, matte finish. Blade - .767" (19.5mm) wide, .319" (8mm) high. Notch - .11" (2.7mm) wide, .07" (1.8mm) deep. Body - .70" (18mm) wide, 1.4" (3.6cm) long.

Mer...

Presisjonsmaskinert for Match Presisjon

Alle komponenter er CNC-frest fra en solid stålblokk for å sikre nøyaktige, repeterbare klikkjusteringer for vind- og høydejustering. Det riflete bakre bladet har en svak revers vinkel for å redusere gjenskinn og forbedre siktebildet. Helt kompatibel med det originale front-siktet på Mk I og Mk II™ pistoler. Passer Ruger® 22 pistoler utstyrt med fabrikkjusterbart baksikte. Ingen tilpasning nødvendig, bruker fabrikkens skråkant; låses på plass med to sett skruer.

SPECS: Stål, blå, matt finish. Blad - .767" (19.5mm) bredt, .319" (8mm) høyt. Hakk - .11" (2.7mm) bredt, .07" (1.8mm) dypt. Kropp - .70" (18mm) bred, 1.4" (3.6cm) lang.

Mer...

Kundevurderinger for VOLQUARTSEN TL 2000 SIGHT

Antall vurderinger: 4
Fra brownells.com: 4
Gjennomsnittsvurdering: 4,8

VOLQUARTSEN VC2TL / TL2000 (17.09.2014)

Fitted this rear sight to my Ruger Comp Mk111. Perfect fit and drifted in tight so it won't move. The two supplied locking screws are great to keep it in place. Sight picture is much improved over stock due to the shallower and narrower notch.

Not so much guess work in aiming now. Better groups. Awesome. Non reflective ribbing on the sight blade is great feature. There is no freeplay in this unit - the stock sight wobbled all over the place. Windage adjustment screw is thankfully much larger than the tiny one on the original sight.

Only downside was the supplied hex key was too loose to safely use - no biggie. Read my review and buy this sight without any reservations. Cheers all, Brad.

Nice quality sight (01.10.2015)

Definitely a tighter fit then what the description leads one to believe. I was installing the sight on a Ruger MKIII Hunter 22/45 and needed a hammer from the get go!

--Pros: upside is that the set screws really are needed and are just here as backups, really high quality part.

--Cons: If you don't have the right hammer/ nylon punch, you could damage the sight or receiver. (you would need a lot of force for either). Also there are no instructions whatsoever, so if you're not mechanically inclined and can figure how things work by analyzing them, try a different sight or let a professional do the installation.

Beside a soft surface to protect the receive, this was the only tool I needed:

http://www.brownells.com/gunsmith-tools-supplies/general-gunsmith-tools/hammers/1-nylon-brass-hammer-prod12588.aspx

It's the Bomar for Ruger .22 Auto's (27.06.2016)

Much better than the stock site that Ruger provides. Adjustments are finer and site picture is much more defined. Solid unit and the only disadvantage is that it must be fitted to the dovetail.

For those that were complaining that there were no instructions here they are:

- Remove the elevation screw all the way out until you can move the leaf forward

- Take out the dual elevation Springs and don't lose them

- Remove the set screws and clean them with acetone along with the holes

- Fit the site base appropriately to the dovetail then drift it in as best as possible so that it is even on both sides with the receiver - Lock down site base with the two set screws using blue Loctite

- Replace the dual elevation springs and screw down the elevation screw

Fitting required (04.08.2018)

Heavy duty and well made. Strong positive clicks. No slop anywhere. Mine required lots of fitting to install. The set screws suggest that this is a drop in part but it is not.

I like a sight picture that leaves only a small clearance on each side of the front sight. This sight delivers that, and is almost too much of a good thing. Mounted on a Ruger MKII 10" target.

For precision shooting, not speed shooting.

Les 4 flere anmeldelser fra brownells.com

1849 1849 1 NOK

Produktnr.: 930000011
VOLQUARTSEN TL 2000 SIGHT
Produsentnr.: VC2TL 810162011734 Alle komponenter er CNC-frest fra en solid stålblokk for å sikre nøyaktige, repeterbare klikkjusteringer for vind- og høydejustering. Det riflete bakre bladet har en svak revers vinkel for å redusere gjenskinn og forbedre siktebildet. Helt kompatibel med det originale front-siktet på Mk I og Mk II™ pistoler. Passer Ruger® 22 pistoler utstyrt med fabrikkjusterbart baksikte. Ingen tilpasning nødvendig, bruker fabrikkens skråkant; låses på plass med to sett skruer.

1849 NOK 3 kr 1 849,00 *

Leveringstid ca. 14-21 dager.
3 stk. på lageret i USA

Spesifikasjoner: Make: Ruger Modell: Mark I, Mark II Sight Color: Black Style: Adjustable, Target, Factory Replacement

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Top takeaways

Alle komponenter er CNC-frest fra solid stål for nøyaktige klikkjusteringer for vind- og høydejustering.
Kompatibel med originale front-sikter på Mk I og Mk II™ pistoler, uten behov for tilpasning.
Riflet bakre blad med revers vinkel for redusert gjenskinn og forbedret siktebilde.

Attributes

Make: Ruger Modell: Mark I,Mark II Sight Color: Black Style: Adjustable,Factory Replacement,Target Leveringsvekt: 0,036kg Frakthøyde: 10mm Fraktbredde: 122mm Fraktlengde: 193mm UPC : 810162011734

Elementdetaljer

Made in USA

Oppgrader din Ruger® med Volquartsen TL 2000 bakre sikt! 🎯 Presise justeringer og enkel montering for Mk I og Mk II. Bestill nå!

Precision Machined For Match Accuracy

SPECS: Steel, blue, matte finish. Blade - .767" (19.5mm) wide, .319" (8mm) high. Notch - .11" (2.7mm) wide, .07" (1.8mm) deep. Body - .70" (18mm) wide, 1.4" (3.6cm) long.

Mer...

Presisjonsmaskinert for Match Presisjon

SPECS: Stål, blå, matt finish. Blad - .767" (19.5mm) bredt, .319" (8mm) høyt. Hakk - .11" (2.7mm) bredt, .07" (1.8mm) dypt. Kropp - .70" (18mm) bred, 1.4" (3.6cm) lang.

Mer...