VOLQUARTSEN
RUGER® MARK II™ HAMMER BUSHING

810162012403 930000056

Close Tolerances For A Smooth, Consistent Trigger Pull

CNC machined from hardened steel to exceptionally close tolerances to help ensure a smooth, consistent trigger pull. Advanced screw machine technology is used to drill and ream the pivot pin hole perfectly concentric for optimal hammer-to-sear engagement. Black oxide finish for added durability and resistance against corrosion.

SPECS: Steel, black oxide finish. Fits Ruger Mark II pistols only.

Mer...

Nøyaktige Toleranser for en Jevn, Konsekvent Avtrekkerfølelse

CNC-maskinert fra herdet stål med ekstremt nøyaktige toleranser for å bidra til en jevn og konsekvent avtrekkerfølelse. Avansert skrue-maskinteknologi brukes for å bore og utvide bolthullet perfekt sentrisk for optimal hammer-til-sear-engasjement. Sortoksidert finish for økt holdbarhet og motstand mot korrosjon.

SPECS: Stål, sortoksidert finish. Passer kun til Ruger Mark II pistoler.

Mer...

Kundevurderinger for VOLQUARTSEN MARK II HAMMER BUSHING

Antall vurderinger: 4
Fra brownells.com: 4
Gjennomsnittsvurdering: 4,3

MKII HAMMER BUSHING (23.02.2010)

If you're going to change out a hammer bushing, the reason you are doing it is to remove that particular point of slop. You don't want the hammer bushing turning inside the hammer's hole. The VQ hammer bushing does improves trigger pull over the factory part but it doesn't completely remove that pivot point between hammer and bushing because it wasn't intended to, it lacks the extra improvement provided by other bushings. However, you can use loctite or little epoxy on a VQ bushing before installing it to hammer in order to hold it solid inside the hammer and eliminate the pivot point.

Great Product (14.11.2010)

Great product, does exactly what it is advertised to do. VERY easy install.

Great replacement part (30.01.2012)

Got this to put in my Mark III 22/45. Very easy to install. This bushing will allow you to take out the magazine disconnect and make your life a whole lot easier when assembling/dissassembling the firearm.

Not as tight fit as Clark (03.02.2016)

This slightly tightens the fit between the hammer and pin. It does not require fitting at all. But it does leave perceptible movement.

The Clark version does require (very simple & easy) fitting, and makes the fit as perfect as you have patience for. It can be made to leave no perceptible movement. But it costs almost triple this one. So, spend a little, get a little, or spend a lot more, get a lot more. How does that Brownells motto go again?

Les 4 flere anmeldelser fra brownells.com

0 0 1 NOK

Produktnr.: 930000056
VOLQUARTSEN MARK II HAMMER BUSHING
Produsentnr.: VC2HB 810162012403 CNC-maskinert fra herdet stål med ekstremt nøyaktige toleranser for å bidra til en jevn og konsekvent avtrekkerfølelse. Avansert skrue-maskinteknologi brukes for å bore og utvide bolthullet perfekt sentrisk for optimal hammer-til-sear-engasjement. Sortoksidert finish for økt holdbarhet og motstand mot korrosjon.

Varsle ved tilgjengelighet

Ikke tilgjengelig.

Spesifikasjoner: Make: Ruger Modell: Mark I, Mark II

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Top takeaways

CNC-maskinert fra herdet stål for en jevn og konsekvent avtrekkerfølelse.
Sortoksidert finish gir økt holdbarhet og motstand mot korrosjon.
Passer kun til Ruger Mark II pistoler.

Attributes

Make: Ruger Modell: Mark I,Mark II Leveringsvekt: 0,005kg Frakthøyde: 8mm Fraktbredde: 71mm Fraktlengde: 86mm UPC : 810162012403