Fits inside face bolt recess to support back side of the extractor rivet while you peen the other end to lock a new extractor in place. Just like the one Remington uses with one "cut" added for better support when clamping in the vise.
SPECS: Blued, tool steel, hardened to Rc 60-63. 2-¼" (5.7cm) high x 1-¾" (4.4cm) wide x ½" (12.7mm)thick.
Mer...
Forenkler peening av ekstraktorriveter
Passer inn i ansiktet på bolthullet for å støtte baksiden av ekstraktorriveten mens du banker den andre enden for å låse en ny ekstraktor på plass. Akkurat som den Remington bruker, men med ett "kutt" lagt til for bedre støtte når den festes i skrustikken.
SPECS: Blånet, verktøystål, herdet til Rc 60-63. 2-¼" (5.7cm) høy x 1-¾" (4.4cm) bred x ½" (12.7mm) tykk.
Mer...
Kundevurderinger for BROWNELLS REMINGTON RIFLE EXTRACTOR RIVET ANVIL
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 5
'Must Have' tool for rivet installs(16.11.2009)
A handy little piece that makes the finished job look 'factory' perfect! Holds the rivet in place so you can peen it properly. All that is left to do is polish the outside of the bolt and you're done.
Better than home-made!(23.12.2010)
Once again, the right tool for the job. Simple, easy to use, solid and should last for years. Beats the shop made tool I've been using, and one person can do it. Not a very versatile tool, will do exactly the one job it was designed for. But, with so many Remington pumps, semi-autos and bolts in the world that use the riveted extractor, it will get used.
Produktnr.: 080740000 BROWNELLS REMINGTON RIFLE EXTRACTOR RIVET ANVIL050806108851 Passer inn i ansiktet på bolthullet for å støtte baksiden av ekstraktorriveten mens du banker den andre enden for å låse en ny ekstraktor på plass. Akkurat som den Remington bruker, men med ett "kutt" lagt til for bedre støtte når den festes i skrustikken.
1099NOK26kr 1 099,00
*
Leveringstid ca. 14-21 dager. Mer enn 10 stk. på lager i USA
Fits inside face bolt recess to support back side of the extractor rivet while you peen the other end to lock a new extractor in place. Just like the one Remington uses with one "cut" added for better support when clamping in the vise.
SPECS: Blued, tool steel, hardened to Rc 60-63. 2-¼" (5.7cm) high x 1-¾" (4.4cm) wide x ½" (12.7mm)thick.
Mer...
Forenkler peening av ekstraktorriveter
Passer inn i ansiktet på bolthullet for å støtte baksiden av ekstraktorriveten mens du banker den andre enden for å låse en ny ekstraktor på plass. Akkurat som den Remington bruker, men med ett "kutt" lagt til for bedre støtte når den festes i skrustikken.
SPECS: Blånet, verktøystål, herdet til Rc 60-63. 2-¼" (5.7cm) høy x 1-¾" (4.4cm) bred x ½" (12.7mm) tykk.
Mer...
Kundevurderinger for BROWNELLS REMINGTON RIFLE EXTRACTOR RIVET ANVIL
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 5
'Must Have' tool for rivet installs(16.11.2009)
A handy little piece that makes the finished job look 'factory' perfect! Holds the rivet in place so you can peen it properly. All that is left to do is polish the outside of the bolt and you're done.
Better than home-made!(23.12.2010)
Once again, the right tool for the job. Simple, easy to use, solid and should last for years. Beats the shop made tool I've been using, and one person can do it. Not a very versatile tool, will do exactly the one job it was designed for. But, with so many Remington pumps, semi-autos and bolts in the world that use the riveted extractor, it will get used.