Over 300 000 kunder - vi takker dere!

40 000+ produkter for jakt og skytesport

Oppgrader din Remington med WOLFF RP avtrekkerfjær! ✨ Reduser avtrekksvekten for bedre nøyaktighet. Passer til modeller 700/721/722.

WOLFF REMINGTON 700/721/722 TRIGGER SPRING - WOLFF REM. RP TRIGGER SPRING

969000173

Attributes

  • Modell: 700,721,722
  • Våpentype: Remington
  • Leveringsvekt: 0,005kg
  • Frakthøyde: 10mm
  • Fraktbredde: 69mm
  • Fraktlengde: 142mm

Elementdetaljer

Made in USA
  • Spesifikasjoner:
  • Make: Remington
  • Modell: 700, 721, 722
279 279 1 NOK
279 NOK kr 279

Priser inkl. mva. pluss levering

Produktnr.: 969000173

Produsentnr.: 33240

Gi din Remington bolt rifle et ytelsesløft med disse enkle å installere fjærene. Redusert kraft (RP) avtrekksfjær bidrar til å senke den opplevde avtrekkskraften for bedre, mer konsistent presisjon.
På lager
1
2
3
4
5
6
7
8
9
10+
  • Spesifikasjoner:
  • Make: Remington
  • Modell: 700, 721, 722

Beskrivelse:

Vis original (engelsk)
Reduser Avtrekkskraft
Gi din Remington bolt rifle et ytelsesløft med disse enkle å installere fjærene. Redusert kraft (RP) avtrekksfjær bidrar til å senke den opplevde avtrekkskraften for bedre, mer konsistent presisjon.

SPECS: Fjærstål. Passer Rem. 700/721/722.

Attributes

  • Modell: 700,721,722
  • Våpentype: Remington
  • Leveringsvekt: 0,005kg
  • Frakthøyde: 10mm
  • Fraktbredde: 69mm
  • Fraktlengde: 142mm

Elementdetaljer

Made in USA

Kundeanmeldelser

Kundevurderinger (3)

2 / 5
Ikke anbefalt

Brownells USA Junk 23.12.2017

The factory spring allowed minimum of 4 lbs. This spring was shorter and stiffer than the factory spring. 6lbs was as low as you could go before the set screw no longer contacted the spring and the rifle became unsafe. Save time and money and go another route.

Anbefalt

Brownells USA Helps a little 26.07.2015

Because Wolff's customer service is not knowledgeable about this product, I ended up going to another company's web site for installation instructions. This spring is NOT the one that goes behind the trigger. DO NOT try to remove the one that goes behind the trigger, and which is tensioned by the screw in the trigger. It goes in the front of the trigger housing assembly. You will need to remove the factory installed sealant to remove the screw that holds this spring in. Also, it is not as long as the one pictured here. It is about 1/3 that length. Trigger pull was reduced to about 3.5 # with this spring installed. That was on a gun that REMINGTON could not (or would not) reduce below 5 #. I sent two NEW rifles back to Remington because of heavy trigger pull. Despite the fact that the hang tag on the brand new guns states, "3 1/2 pounds out of the box" , Remington was unable to actually bring the guns into spec. The guns were returned to me with a heavy trigger pull, and a note explaining that they adjusted to 4.5# and 5.5 #, NOT 3.5. This spring helped, but keep in mind you will need to void the Remington warranty to bring it into Remington spec.

Kunder kjøpte også

Oops! Noe gikk galt.

Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden på nytt for å fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.

Tilbake til toppen