Over 300 000 kunder - vi takker dere!

40 000+ produkter for jakt og skytesport

850035804827 430111389
R2 FLASH HIDERS These fit Plan B type mounts. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned. Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly. FEATURES: 17-4 PH Atlas and Atlas XL compatible Plan B compatible Black Nitride finish (67 HRC Surface hardness) Shims not included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
1599 1649 4 NOK
New
Produktnr.: 430111389
REARDEN MANUFACTURING GROUP LLC R2 FLASH HIDER 1/2-28 THREADS SQUARE SHOULDER BLACK NITRIDE
Produsentnr.: 10083 850035804827
1599 NOK 0 kr 1 599,00 *
Varsle ved tilgjengelighet
Utsolgt. Ingen leveringsdato kjent.
Spesifikasjoner: Finish: Black Kaliber: 375 Caliber (.375) Material: Stainless Steel Threads: 1/2-28

Attributes

Finish: Black Gjenger: 1/2-28 Kaliber: 375 Caliber (.375) Material: Stainless Steel Leveringsvekt: 0,227kg Frakthøyde: 152mm Fraktbredde: 38mm Fraktlengde: 102mm UPC : 850035804827

Elementdetaljer

Made in USA



New
Produktnr.: 430111391
REARDEN MANUFACTURING GROUP LLC R2 FLASH HIDER 13.5X1LH THREADS TAPER SHOULDER BLACK NITRIDE
Produsentnr.: 10106 850035804940
1649 NOK 4 kr 1 649,00 *
Leveringstid ca. 14-21 dager.
4 stk. på lageret i USA
Spesifikasjoner: Finish: Black Kaliber: 375 Caliber (.375) Material: Stainless Steel Threads: M13.5x1LH

Attributes

Finish: Black Gjenger: M13.5x1LH Kaliber: 375 Caliber (.375) Material: Stainless Steel Leveringsvekt: 0,227kg Frakthøyde: 152mm Fraktbredde: 102mm Fraktlengde: 152mm UPC : 850035804940

Elementdetaljer

Made in USA


New
Produktnr.: 430111390
REARDEN MANUFACTURING GROUP LLC R2 FLASH HIDER 5/8-24 THREADS SQUARE SHOULDER BLACK NITRIDE
Produsentnr.: 10100 850035804889
1599 NOK 0 kr 1 599,00 *
Varsle ved tilgjengelighet
Utsolgt. Ingen leveringsdato kjent.
Spesifikasjoner: Finish: Black Kaliber: 375 Caliber (.375) Material: Stainless Steel Threads: 5/8-24

Attributes

Finish: Black Gjenger: 5/8-24 Kaliber: 375 Caliber (.375) Material: Stainless Steel Leveringsvekt: 0,227kg Frakthøyde: 152mm Fraktbredde: 38mm Fraktlengde: 102mm UPC : 850035804889

Elementdetaljer

Made in USA

New
Produktnr.: 430111392
REARDEN MANUFACTURING GROUP LLC R2 FLASH HIDER 14X1 LH THREADS FACEMOUNT SHOULDER BLACK
Produsentnr.: 10112 850041491004
1649 NOK 0 kr 1 649,00 *
Varsle ved tilgjengelighet
Utsolgt. Ingen leveringsdato kjent.
Spesifikasjoner: Finish: Black Kaliber: 375 Caliber (.375) Material: Stainless Steel Threads: M14x1LH

Attributes

Finish: Black Gjenger: M14x1LH Kaliber: 375 Caliber (.375) Material: Stainless Steel Leveringsvekt: 0,227kg UPC : 850041491004

Elementdetaljer

Made in USA

R2 FLASH HIDERS These fit Plan B type mounts. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned. Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly. FEATURES: 17-4 PH Atlas and Atlas XL compatible Plan B compatible Black Nitride finish (67 HRC Surface hardness) Shims not included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
Tilbake til toppen