Fully-machined hardened steel mount with three-point mounting, provides a stable, secure base for mounting large objective scopes. Easily clamps to the charger guide dovetail and receiver mount lug without modifications to rifle. Heavy, forward locking screw gives rock solid stability at the receiver ring. Sight channel allows back-up use of iron sights without removing scope.
Fullstendig maskinert herdet stålmontering med tredelt feste, gir en stabil og sikker base for montering av store objektivkikkerter. Festes enkelt til ladegrepets dovetail og våpenets feste uten modifikasjoner på riflen. Tung, fremoverlåsende skrue gir solid stabilitet ved mottakerens ring. Siktekanalen tillater bruk av jernsikter som backup uten å fjerne kikkerten.
SPECS: 4140 stål, svart, nitridfinish. Herdet til Rc 60-62. 5,38" (13,6cm) lang. 1,875" (4,7cm) høy. Veier 10,9 oz (310 g).
Mer...
Kundevurderinger for SMITH ENTERPRISE M14 SCOPE MOUNT
Antall vurderinger: 3
Fra brownells.com: 3
Gjennomsnittsvurdering: 3,3
Should have bought a Sadlak.(14.11.2010)
I've been trying to get this mount to work for over 3 yrs. Shoots 20" high with MK IV scope adjusted to full down limit (that's 45 minutes down from mechanical center). Tried different rings (Smith, Burris Signature), adding shims between rings and mount, raising front of mount with forward setscrew. Shoots groups under 1" @ 100yds when installed per instructions with Smith rings, but 20" high. Shot like a shotgun (6" groups) with other attempts to lower point of impact. Mount manufacturer said SA, NM, M1A not manufactured to tolerance. It groups under an inch! Should have bought a Sadlak.
One of the Best Mounts for M1A/M14(16.12.2010)
This is a good Mount. A little more difficult to install than a regular mount like bolt guns but this is due to the nature of the M14. Sadlak and Smith Enterprise are very much alike if not exactly. The Mounts are manufactured to G.I. receiver specs. I have installed these on many M14's in Iraq. But some Springfield's Receivers are not to G.I. specs. You can send the rifle to Smith Enterprise or another competent gunsmith who is good with these style of rifles. I would recommend this mount wholeheartedly. I've never had problems with it that could not be overcame.
Rock Solid(09.08.2012)
Great mount, not the easiest to install but well worth the time and money. Before trying to put it on - Read the instructions!
Produktnr.: 851000001 SMITH ENTERPRISE M14 SCOPE MOUNT Produsentnr.: 2006 Fullstendig maskinert herdet stålmontering med tredelt feste, gir en stabil og sikker base for montering av store objektivkikkerter. Festes enkelt til ladegrepets dovetail og våpenets feste uten modifikasjoner på riflen. Tung, fremoverlåsende skrue gir solid stabilitet ved mottakerens ring. Siktekanalen tillater bruk av jernsikter som backup uten å fjerne kikkerten.
7799NOK4kr 7 799,00
*
Leveringstid ca. 14-21 dager. 4 stk. på lageret i USA
Fullstendig maskinert herdet stålmontering som gir en stabil og sikker base for store objektivkikkerter uten modifikasjoner på riflen.
Siktekanalen tillater bruk av jernsikter som backup uten å fjerne kikkerten.
Spesifikasjoner: 4140 stål, svart nitridfinish, herdet til Rc 60-62, 5,38" lang, 1,875" høy, veier 10,9 oz.
Attributes
Farge:
Black
Make:
Springfield
Material:
Steel
Modell:
M14,M1A
Number of Bases:
1-Piece
Style:
Tactical Bases
Leveringsvekt: 0,363kgFrakthøyde: 41mmFraktbredde: 91mmFraktlengde: 165mm
Elementdetaljer
Made in USA
Oppdag M14 Tactical Scope Mount 🔭 fra Smith Enterprise. Solid stålmontering for sikker montering av kikkertsikter uten modifikasjoner.
Fully-machined hardened steel mount with three-point mounting, provides a stable, secure base for mounting large objective scopes. Easily clamps to the charger guide dovetail and receiver mount lug without modifications to rifle. Heavy, forward locking screw gives rock solid stability at the receiver ring. Sight channel allows back-up use of iron sights without removing scope.
Fullstendig maskinert herdet stålmontering med tredelt feste, gir en stabil og sikker base for montering av store objektivkikkerter. Festes enkelt til ladegrepets dovetail og våpenets feste uten modifikasjoner på riflen. Tung, fremoverlåsende skrue gir solid stabilitet ved mottakerens ring. Siktekanalen tillater bruk av jernsikter som backup uten å fjerne kikkerten.
SPECS: 4140 stål, svart, nitridfinish. Herdet til Rc 60-62. 5,38" (13,6cm) lang. 1,875" (4,7cm) høy. Veier 10,9 oz (310 g).
Mer...
Kundevurderinger for SMITH ENTERPRISE M14 SCOPE MOUNT
Antall vurderinger: 3
Fra brownells.com: 3
Gjennomsnittsvurdering: 3,3
Should have bought a Sadlak.(14.11.2010)
I've been trying to get this mount to work for over 3 yrs. Shoots 20" high with MK IV scope adjusted to full down limit (that's 45 minutes down from mechanical center). Tried different rings (Smith, Burris Signature), adding shims between rings and mount, raising front of mount with forward setscrew. Shoots groups under 1" @ 100yds when installed per instructions with Smith rings, but 20" high. Shot like a shotgun (6" groups) with other attempts to lower point of impact. Mount manufacturer said SA, NM, M1A not manufactured to tolerance. It groups under an inch! Should have bought a Sadlak.
One of the Best Mounts for M1A/M14(16.12.2010)
This is a good Mount. A little more difficult to install than a regular mount like bolt guns but this is due to the nature of the M14. Sadlak and Smith Enterprise are very much alike if not exactly. The Mounts are manufactured to G.I. receiver specs. I have installed these on many M14's in Iraq. But some Springfield's Receivers are not to G.I. specs. You can send the rifle to Smith Enterprise or another competent gunsmith who is good with these style of rifles. I would recommend this mount wholeheartedly. I've never had problems with it that could not be overcame.
Rock Solid(09.08.2012)
Great mount, not the easiest to install but well worth the time and money. Before trying to put it on - Read the instructions!