LEE PRECISION
BULGE BUSTER

734307904876 100010151

Push through die adapter will quickly remove the annoying bulge rings that shell holder constrained dies simply can't reach Bulge Buster Kit includes: extension sleeve, push through punch, catch container and complete instructions. Use with your Lee Factory Crimp Die Will ONLY work with these cases: 380 ACP, 10mm, 40 S&W, 41 AE (Use .40 S&W Factory Crimp Die), 45 ACP, 45 GAP, and 45 Win Mag. The Lee Carbide Factory Crimp Die is required and must be purchased separately. This die requires the purchase of the appropriate caliber Lee factory crimp die along with the bulge buster kit. Lee does not recommend the use of this kit on cartridges that were fired thru Glock pistols or any other pistol that does not completely support the case head when round is chambered.

Mer...

Push through die-adapteren vil raskt fjerne de irriterende bulgeringene som hylseholderbegrensede matriser rett og slett ikke kan nå. Bulge Buster-settet inkluderer: forlengerskuffe, gjennomstøtingsstempel, oppsamlingsbeholder og komplette instruksjoner. Brukes med din Lee Factory Crimp Die. Vil KUN fungere med disse hylsene: 380 ACP, 10mm, 40 S&W, 41 AE (bruk .40 S&W Factory Crimp Die), 45 ACP, 45 GAP, og 45 Win Mag. Lee Carbide Factory Crimp Die er nødvendig og må kjøpes separat. Denne matrisen krever kjøp av den passende kaliber Lee factory crimp die sammen med Bulge Buster-settet. Lee anbefaler ikke bruk av dette settet på patroner som ble avfyrt gjennom Glock-pistoler eller andre pistoler som ikke fullstendig støtter hylsehodet når patronen er kamret.

Mer...

Kundevurderinger for LEE PRECISION LEE BULGE BUSTER

Antall vurderinger: 4
Fra brownells.com: 4
Gjennomsnittsvurdering: 3,8

Lee Bulge Buster (17.10.2012)

I just purchased a Bulge Buster,for use on my .40S&W, and .45 ACP cases. I have only processed about 25 of each caliber to initially try it out. It works great, the processed cases will drop into a EGW chamber checker, without force. My only complaint is that since the case just sits on the "ram". it is necessary to insert the case into the Lee carbide die, then use the ram to push it through. It is a bit awkward. But it seems to work very well.

Don't make the same mistake as me (20.02.2013)

I missed the bit about needing a factory crimp die, Its not as cheap or as useful as it seems.
True, waiting two months for the NZ police to issue a permit didn't help my mood, suppose if you pay peanuts..

Lee 45 ACP bulge buster (04.07.2015)

Purchased a Lee 45 ACP bulge buster to eliminate the random bulged "range brass" I reload. Seems Glock semi-auto's like to leave bulged cases. This is easy to set up using my Lee 45 ACP crimp die and breech lock single stage press. I always double check my reloads with my L.E.Wilson case gage to make sure they will chamber. Nice die / device to have on hand for when those pesky bulged cases show up. Lee, in my opinion, makes a great product at an affordable price. I use Lee dies exclusively for all of my pistol and revolver reloading.

Works Perfectly! Precision Shooter Need (01.01.2017)

I purchased bulge buster to eliminate the bulged "brass" I had from matches and the occasional reload that failed in the chamber check gauge. My 1911s are all full custom and have custom reamed chambers. Anything out of spec isn't going through, not just from sloppy unsupported polymer chambers, but factory 1911s as well. Therefore I check every round and previously discarded a lot of brass and had to take apart a lot of reloaded ammunition. With the bulge buster you can re-size (fully) out of spec brass or fully loaded ammunition. Absolute win. What I didn't know was that carbide dies don't fully size brass, however, I'm not going to switch for pistol due to the need to lube. This device allows you to have the best of both worlds.

PLEASE NOTE! You will need to purchase a Lee crimp die separately (get carbide). Because the pusher moves the brass totally through it will fully size regardless. I wish the pusher could capture the brass better, but it's not possible as it has to pass totally through the die.

Les 4 flere anmeldelser fra brownells.com

399 399 1 NOK

Produktnr.: 100010151
LEE PRECISION LEE BULGE BUSTER
Produsentnr.: 90487 734307904876 Push through die-adapteren vil raskt fjerne de irriterende bulgeringene som hylseholderbegrensede matriser rett og slett ikke kan nå. Bulge Buster-settet inkluderer: forlengerskuffe, gjennomstøtingsstempel, oppsamlingsbeholder og komplette instruksjoner. Brukes med din Lee Factory Crimp Die. Vil KUN fungere med disse hylsene: 380 ACP, 10mm, 40 S&W, 41 AE (bruk .40 S&W Factory Crimp Die), 45 ACP, 45 GAP, og 45 Win Mag. Lee Carbide Factory Crimp Die er nødvendig og må kjøpes separat. Denne matrisen krever kjøp av den passende kaliber Lee factory crimp die sammen med Bulge Buster-settet. Lee anbefaler ikke bruk av dette settet på patroner som ble avfyrt gjennom Glock-pistoler eller andre pistoler som ikke fullstendig støtter hylsehodet når patronen er kamret.

399 NOK 0 kr 399,00 *

Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.

Spesifikasjoner: Die Style: Specialty Dies Kaliber: 45 Auto (ACP), 380 Auto (ACP), 10 mm Auto, 40 S&W, 45 G.A.P, 45 Winchester Magnum

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Top takeaways

Bulge Buster-settet fjerner raskt bulgeringer som andre matriser ikke kan nå, og inkluderer nødvendige deler og instruksjoner.
Settet fungerer kun med spesifikke hylser: 380 ACP, 10mm, 40 S&W, 41 AE, 45 ACP, 45 GAP, og 45 Win Mag, og krever en separat kjøpt Lee Carbide Factory Crimp Die.
Lee anbefaler ikke bruk av Bulge Buster-settet på patroner avfyrt gjennom Glock-pistoler eller andre pistoler som ikke fullstendig støtter hylsehodet.

Attributes

Cartridge: 380 Auto (ACP),40 S&W,10 mm Auto,45 Auto (ACP),45 G.A.P,45 Winchester Magnum Die Style: Specialty Dies Leveringsvekt: 0,181kg Frakthøyde: 122mm Fraktbredde: 84mm Fraktlengde: 84mm UPC : 734307904876