Forster's easy-to-use hand-held neck turning tool helps you take the next step toward cartridge-to-cartridge consistency. It features a carbide cutter with a micrometer-style adjustment knob for precise material removal to give cases consistent wall thickness that improves bullet-to-bore alignment. The aluminum holder retains the case firmly with a simple turn of the knob; holds up to .592" base diameter. Requires a pilot that's specific to the case mouth diameter; sold separately. Pilots are precision-ground .002" to .0025" smaller than the bullet diameter. Forster Hand Held Outside Neck Turner Pilots can be located HERE.
Mer...
Forsters brukervennlige håndholdte verktøy for utvendig halsdreining hjelper deg med å ta steget videre mot konsistens fra patron til patron. Den har en hardmetallkutter med en mikrometerjusteringsknott for presis fjerning av materiale for å gi hylsene en jevn veggtykkelse som forbedrer kule-til-løp justeringen. Aluminiumsholderen beholder hylsen fast med en enkel vridning av knotten; holder opptil .592" base diameter. Krever en pilot som er spesifikk for hylsemunningens diameter; selges separat. Pilotene er presisjonsslipt .002" til .0025" mindre enn kulediameteren. Forster Hand Held Outside Neck Turner Piloter kan finnes HER.
Mer...
Kundevurderinger for FORSTER PRODUCTS, INC. HAND HELD OUTSIDE NECK TURNER
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 2
t handle slips on case(10.07.2012)
I bought this neck turner a while back. the cutter works well, but the handle that holds the brass slips often if not all the time. I got a little upset and bought the sinclair nt 4000. Now your talkin about neck turning..
Buy the Sinclair(26.04.2014)
Will turn the cases if you can get the shell holder to hold the case in position. VERY bad design, I'll sell you one cheap. Buy the Sinclair instead.
Produktnr.: 749012890 FORSTER PRODUCTS, INC. HAND HELD OUTSIDE NECK TURNER Produsentnr.: HOT100757253020032 Forsters brukervennlige håndholdte verktøy for utvendig halsdreining hjelper deg med å ta steget videre mot konsistens fra patron til patron. Den har en hardmetallkutter med en mikrometerjusteringsknott for presis fjerning av materiale for å gi hylsene en jevn veggtykkelse som forbedrer kule-til-løp justeringen. Aluminiumsholderen beholder hylsen fast med en enkel vridning av knotten; holder opptil .592" base diameter. Krever en pilot som er spesifikk for hylsemunningens diameter; selges separat. Pilotene er presisjonsslipt .002" til .0025" mindre enn kulediameteren. Forster Hand Held Outside Neck Turner Piloter kan finnes HER.
1699NOK2kr 1 699,00
*
Leveringstid ca. 14-21 dager. 2 stk. på lageret i USA
Forster's easy-to-use hand-held neck turning tool helps you take the next step toward cartridge-to-cartridge consistency. It features a carbide cutter with a micrometer-style adjustment knob for precise material removal to give cases consistent wall thickness that improves bullet-to-bore alignment. The aluminum holder retains the case firmly with a simple turn of the knob; holds up to .592" base diameter. Requires a pilot that's specific to the case mouth diameter; sold separately. Pilots are precision-ground .002" to .0025" smaller than the bullet diameter. Forster Hand Held Outside Neck Turner Pilots can be located HERE.
Mer...
Forsters brukervennlige håndholdte verktøy for utvendig halsdreining hjelper deg med å ta steget videre mot konsistens fra patron til patron. Den har en hardmetallkutter med en mikrometerjusteringsknott for presis fjerning av materiale for å gi hylsene en jevn veggtykkelse som forbedrer kule-til-løp justeringen. Aluminiumsholderen beholder hylsen fast med en enkel vridning av knotten; holder opptil .592" base diameter. Krever en pilot som er spesifikk for hylsemunningens diameter; selges separat. Pilotene er presisjonsslipt .002" til .0025" mindre enn kulediameteren. Forster Hand Held Outside Neck Turner Piloter kan finnes HER.
Mer...
Kundevurderinger for FORSTER PRODUCTS, INC. HAND HELD OUTSIDE NECK TURNER
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 2
t handle slips on case(10.07.2012)
I bought this neck turner a while back. the cutter works well, but the handle that holds the brass slips often if not all the time. I got a little upset and bought the sinclair nt 4000. Now your talkin about neck turning..
Buy the Sinclair(26.04.2014)
Will turn the cases if you can get the shell holder to hold the case in position. VERY bad design, I'll sell you one cheap. Buy the Sinclair instead.