CYLINDER & SLIDE
C&S BROWNING HI-POWER TRIGGER PULL REDUCTION SPRING KIT

000000002516 206025001

Reduces Pull Weight For A Light, Crisp Trigger Pull

Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.

SPECS: Spring steel. #25A includes (3) springs. #25B include (2) springs.

Mer...

Reduserer Trekkvekt For En Lett, Skarp Triggerfølelse

Konkurransetrigger fjærsett reduserer trekkvekten på tunge fabrikktriggere med omtrent 2½ lbs. for en mye forbedret triggerfølelse og bedre nøyaktighet. #25A passer alle Browning Hi-Power pistoler produsert før ‘91, og inkluderer (1) 22 lb. hammerfjær, (1) redusert kraft triggerreturfjær, og (1) redusert kraft tennstiftfjær. #25B passer Browning Hi-Power pistoler produsert fra 1991 og senere, og inkluderer (1) 22 lb. hammerfjær og (1) redusert kraft tennstiftfjær.

SPECS: Fjærstål. #25A inkluderer (3) fjærer. #25B inkluderer (2) fjærer.

Mer...

Kundevurderinger for CYLINDER & SLIDE #25-A SPRING KIT

Antall vurderinger: 4
Fra brownells.com: 4
Gjennomsnittsvurdering: 3,3

Misleading (31.05.2012)

I installed these springs on a new BHP MK3 which originally measured 9.25 lbs at the trigger. After installation the trigger measured 9.25 lbs. The hammer spring was 4 coils longer than the stock or another manutacturer's replacement springs. This means you either have to cut the coils or pre-load the spring extensively to install it on the strut. So unless your hammer / sear interface angle is positive or neutral with really rough surfaces these parts will do little to help the trigger pull. Modifications to the sear spring pressure will however produce changes in the trigger pull weight.

It work !! (25.01.2010)

I just installed the 3 springs in my 1973 BHP
the job it self require some smithing ability , some roll pin in the trigger group are hard to punch out. The Hammer spring is also tricky to replace. The easiest part is the firing pin spring. My High power lost is rock hard trigger and now has a much more manageable trigger pull.
while I was there I also removed the Mag release safety spring. which also help the trigger pull.
Good luck

excellent (01.10.2011)

great spring set, works really well to improve trigger pull and still reliable.

BUT the hammer spring is a bit of a pain to replace (no fault of this set, just be aware) so allow some time or get some advice.

Decent kit, but there were some problems (08.04.2013)

Decided to replace the springs with lighter ones along with a trigger job on the old Hi-power. Installation was a breeze, and everything was good until I reassembled the gun and it would not function correctly. The hammer was binding. Took it all apart and found the replacement spring for the hammer was about 1/4" longer than the original and was fully compressed and binding before the hammer was fully cocked. Ended up having to cut the spring down to get it to the correct length. After that everything functions fine. The kit I ordered was part no. 206-025-001 for the pre-91 Hi-power, as my Hi-power is a 1973. Maybe I got the spring from a later Hi-power by mistake? Not too sure.

Les 4 flere anmeldelser fra brownells.com

549 599 2 NOK

Produktnr.: 206025001
CYLINDER & SLIDE #25-A SPRING KIT
Produsentnr.: CS0025A 000000002516 Konkurransetrigger fjærsett reduserer trekkvekten på tunge fabrikktriggere med omtrent 2½ lbs. for en mye forbedret triggerfølelse og bedre nøyaktighet. #25A passer alle Browning Hi-Power pistoler produsert før ‘91, og inkluderer (1) 22 lb. hammerfjær, (1) redusert kraft triggerreturfjær, og (1) redusert kraft tennstiftfjær. #25B passer Browning Hi-Power pistoler produsert fra 1991 og senere, og inkluderer (1) 22 lb. hammerfjær og (1) redusert kraft tennstiftfjær.

599 NOK 1 kr 599,00 *

Leveringstid ca. 14-21 dager.
1 stk. på lageret i USA

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Top takeaways

Konkurransetrigger fjærsett reduserer trekkvekten på tunge fabrikktriggere med omtrent 2½ lbs, noe som forbedrer triggerfølelsen og nøyaktigheten.
#25A passer alle Browning Hi-Power pistoler produsert før ‘91 og inkluderer (1) 22 lb. hammerfjær, (1) redusert kraft triggerreturfjær, og (1) redusert kraft tennstiftfjær.
#25B passer Browning Hi-Power pistoler produsert fra 1991 og senere, og inkluderer (1) 22 lb. hammerfjær og (1) redusert kraft tennstiftfjær.

Attributes

Leveringsvekt: 0,009kg Fraktbredde: 83mm Fraktlengde: 152mm UPC : 000000002516

Elementdetaljer

Made in USA

Produktnr.: 206025002
CYLINDER & SLIDE #25-B SPRING KIT
Produsentnr.: CS0025B 000000000253 Konkurransetrigger fjærsett reduserer trekkvekten på tunge fabrikktriggere med omtrent 2½ lbs. for en mye forbedret triggerfølelse og bedre nøyaktighet. #25A passer alle Browning Hi-Power pistoler produsert før ‘91, og inkluderer (1) 22 lb. hammerfjær, (1) redusert kraft triggerreturfjær, og (1) redusert kraft tennstiftfjær. #25B passer Browning Hi-Power pistoler produsert fra 1991 og senere, og inkluderer (1) 22 lb. hammerfjær og (1) redusert kraft tennstiftfjær.

549 NOK 0 kr 549,00 *