Over 300 000 kunder - vi takker dere!

40 000+ produkter for jakt og skytesport

FORWARD CONTROLS DESIGN
BACKUP IRON SIGHT W/TRITIUM FOR GLOCK G43X/G48

697566711152 430103596
BIS, G43X/48 (Backup Iron Sight, G43X/G48) is a collaboration between Ameriglo and FCD. Specifically made for Glock G43X and G48, these sights are based on the superb Ameriglo GL-527 with a front sight height of 0.450", and a rear sight height of 0.554", this sight sets provide lower 1/3 co-witness with the Trijicon RMRcc when used with the OPF-G43X/43, RMRcc on G43X and G48. BIS, G43X/48 consists of the following: Front sight, available with either green Tritium and white outline (no serrations), or serrated front sight, no tritium or white outline. Rear sight, serrated. BIS, G43X/48 is slightly different from GL-527 on which it's based. These FCD particular changes are: Tritium option for the front sight. Front sight back strap angle is steeper (25 degrees on the serrated, non-tritium front sight, 20 degrees on non-serrated, tritium front sight) to mitigate snagging when the pistol is drawn from and out of the holster where it's likely to encounter clothing, and the front sight's top corners are softened. Rear sight is horizontally serrated. Designed and made in the USA. Special thanks to the professionals at Ameriglo https://ameriglo.com/ that made this project possible, Forward Controls Design are grateful for their willingness to work with a small outfit for their shared customers / users. G43X/49 with RMRcc is approved by many agencies, most of which require red dot pistols be equipped with metallic, co-witnessing backup sights for both on and off duty use. BIS, G43X/48 was created with them in mind. NOTE: If you don't have a sight pusher or the equipment to install rear sights, please bring it to a qualified and competent gunsmith to perform the installation. It's not uncommon to have to fit the rear sight to the dovetail, a competent gunsmith should be well familiar with the reason and method. Forward Controls Design have seen more than enough expensive muzzle devices ruined by "gunsmiths" that used a screw driver to install them instead of a torque wrench, and hand tightened optics plate screws when a torque value is clearly noted in multiple places. Rather than being loose (easy to install), Forward Controls Design prefer the sights be tight, so it won't be knocked off zero easily. Tolerances of the dovetail and sights also come into play, which results in some being easier, while others are harder to install. A qualified gunsmith can deal with these easily.  
1949 1949 1 NOK
Produktnr.: 430103596
FORWARD CONTROLS DESIGN GLOCK G43X/G48 BACKUP IRON SIGHT WITH TRITIUM
Produsentnr.: BIS, 43X/48, WI 697566711152 BIS, G43X/48 (Backup Iron Sight, G43X/G48) er et samarbeid mellom Ameriglo og FCD. Spesiallaget for Glock G43X og G48, er disse siktebasert på det utmerkede Ameriglo GL-527 med en frontsiktehøyde på 0.450", og et baksiktehøyde på 0.554", disse siktesettene gir en nedre 1/3 co-witness med Trijicon RMRcc når de brukes med OPF-G43X/43, RMRcc på G43X og G48. BIS, G43X/48 består av følgende: Frontsikte, tilgjengelig med enten grønt Tritium og hvit kontur (uten riller), eller riflet frontsikte, uten tritium eller hvit kontur. Baksikte, riflet. BIS, G43X/48 er litt forskjellig fra GL-527 som det er basert på. Disse spesifikke endringene fra FCD er: Tritium-alternativ for frontsiktet. Vinkelen på frontsiktets bakre stropp er brattere (25 grader på det riflede, ikke-tritium frontsiktet, 20 grader på det ikke-riflede, tritium frontsiktet) for å redusere hekting når pistolen trekkes fra og ut av hylsteret der det sannsynligvis vil komme i kontakt med klær, og topphjørnene på frontsiktet er mykgjort. Baksiktet er horisontalt riflet. Designet og produsert i USA. Spesiell takk til profesjonelle hos Ameriglo https://ameriglo.com/ som gjorde dette prosjektet mulig, Forward Controls Design er takknemlige for deres villighet til å samarbeide med en liten aktør for deres felles kunder / brukere. G43X/49 med RMRcc er godkjent av mange etater, de fleste av dem krever at pistoler med rødpunktsikte er utstyrt med metalliske, co-witnessing backup-sikter for både tjeneste og privat bruk. BIS, G43X/48 ble skapt med dem i tankene. MERK: Hvis du ikke har en sikteskyver eller utstyret til å installere baksikter, vennligst ta det med til en kvalifisert og kompetent børsemaker for å utføre installasjonen. Det er ikke uvanlig å måtte tilpasse baksiktet til svalehalen, en kompetent børsemaker bør være godt kjent med grunnen og metoden. Forward Controls Design har sett mer enn nok dyre munningenheter ødelagt av "børsemakere" som brukte en skrutrekker for å installere dem i stedet for en momentnøkkel, og håndstrammet optikkplate-skruer når en momentverdi tydelig er notert flere steder. I stedet for å være løs (lett å installere), foretrekker Forward Controls Design at sikte er stramt, slik at det ikke lett blir slått av null. Toleranser for svalehalen og sikter kommer også i spill, noe som resulterer i at noen er lettere, mens andre er vanskeligere å installere. En kvalifisert børsemaker kan enkelt håndtere disse.
1949 NOK 4 kr 1 949,00 *
Leveringstid ca. 14-21 dager.
4 stk. på lageret i USA
Spesifikasjoner: Make: Glock Modell: 48, 43X Sight Color: Green Style: Tritium

Top takeaways

  1. BIS, G43X/48 er spesiallaget for Glock G43X og G48, og gir en nedre 1/3 co-witness med Trijicon RMRcc.
  2. Frontsiktet er tilgjengelig med grønt Tritium og hvit kontur eller som riflet uten Tritium, mens baksiktet er horisontalt riflet.
  3. Designet og produsert i USA, med spesifikke endringer fra FCD for å redusere hekting og øke brukervennlighet ved trekking fra hylster.

Attributes

Make: Glock Modell: 43X,48 Sight Color: Green Style: Tritium Leveringsvekt: 0,363kg Frakthøyde: 5mm Fraktbredde: 152mm Fraktlengde: 102mm UPC : 697566711152

Elementdetaljer

Made in USA




Oppdag BIS, G43X/48 med Tritium for Glock G43X/G48. 🌟 Perfekt for co-witness med RMRcc. Designet for presisjon og kvalitet!

BIS, G43X/48 (Backup Iron Sight, G43X/G48) is a collaboration between Ameriglo and FCD. Specifically made for Glock G43X and G48, these sights are based on the superb Ameriglo GL-527 with a front sight height of 0.450", and a rear sight height of 0.554", this sight sets provide lower 1/3 co-witness with the Trijicon RMRcc when used with the OPF-G43X/43, RMRcc on G43X and G48. BIS, G43X/48 consists of the following: Front sight, available with either green Tritium and white outline (no serrations), or serrated front sight, no tritium or white outline. Rear sight, serrated. BIS, G43X/48 is slightly different from GL-527 on which it's based. These FCD particular changes are: Tritium option for the front sight. Front sight back strap angle is steeper (25 degrees on the serrated, non-tritium front sight, 20 degrees on non-serrated, tritium front sight) to mitigate snagging when the pistol is drawn from and out of the holster where it's likely to encounter clothing, and the front sight's top corners are softened. Rear sight is horizontally serrated. Designed and made in the USA. Special thanks to the professionals at Ameriglo https://ameriglo.com/ that made this project possible, Forward Controls Design are grateful for their willingness to work with a small outfit for their shared customers / users. G43X/49 with RMRcc is approved by many agencies, most of which require red dot pistols be equipped with metallic, co-witnessing backup sights for both on and off duty use. BIS, G43X/48 was created with them in mind. NOTE: If you don't have a sight pusher or the equipment to install rear sights, please bring it to a qualified and competent gunsmith to perform the installation. It's not uncommon to have to fit the rear sight to the dovetail, a competent gunsmith should be well familiar with the reason and method. Forward Controls Design have seen more than enough expensive muzzle devices ruined by "gunsmiths" that used a screw driver to install them instead of a torque wrench, and hand tightened optics plate screws when a torque value is clearly noted in multiple places. Rather than being loose (easy to install), Forward Controls Design prefer the sights be tight, so it won't be knocked off zero easily. Tolerances of the dovetail and sights also come into play, which results in some being easier, while others are harder to install. A qualified gunsmith can deal with these easily.  
Tilbake til toppen