Over 300 000 kunder - vi takker dere!

40 000+ produkter for jakt og skytesport

Oppdag AR-15/M16 GAS BLOCK TAPER PIN REAMER fra BROWNELLS! 🔧 Perfekt for nøyaktig justering av gassblokkeringspinnen.
  • BROWNELLS TAPER PIN REAMER
  • BROWNELLS TAPER PIN REAMER
  • BROWNELLS TAPER PIN REAMER

BROWNELLS AR-15/M16 GAS BLOCK TAPER PIN REAMER - BROWNELLS TAPER PIN REAMER

050806006645 080000674

Attributes

  • Våpentype: AR-15
  • Leveringsvekt: 0,023kg
  • Frakthøyde: 23mm
  • Fraktbredde: 23mm
  • Fraktlengde: 170mm
  • UPC: 050806006645

Elementdetaljer

Made in USA
  • Spesifikasjoner:
  • Make: AR-15
949 949 1 NOK
Sale
854.1 NOK kr 854,10 kr 949

Priser inkl. mva. pluss levering

Produktnr.: 080000674

050806006645 Høyhastighetsstålen reamer er presist taperet for å matche formen på standard A2 gassblokkens festepinne. Renser eksisterende hull eller taper nyborede hull for å sikre en positiv, sikker passform og presis justering av siktesøylen.
Kommer til lager
1
2
3
4
5
6
7
8
9
10+
  • Spesifikasjoner:
  • Make: AR-15

Beskrivelse:

Vis original (engelsk)
Presist Fullfører Gassblokk/Fremre Siktesøyle Pinhull
Høyhastighetsstålen reamer er presist taperet for å matche formen på standard A2 gassblokkens festepinne. Renser eksisterende hull eller taper nyborede hull for å sikre en positiv, sikker passform og presis justering av siktesøylen.

SPECS: Reamer – Høyhastighetsstål, 2/0 reamer. Taper fra .1137" (2.8mm) O.D. ved spissen til .1462" (3.7mm) O.D. nær skaftet. Håndtak – 2¾" (70mm) lang, 5⁄8" (16mm) diameter.

Attributes

  • Våpentype: AR-15
  • Leveringsvekt: 0,023kg
  • Frakthøyde: 23mm
  • Fraktbredde: 23mm
  • Fraktlengde: 170mm
  • UPC: 050806006645

Elementdetaljer

Made in USA

Kundeanmeldelser

Kundevurderinger (12)

2 / 5
Anbefalt

Brownells USA Works very well 16.07.2017

The handle is small (about ~5/8" dia.) and not useable, so I took it off. Very easy to do, put the cutting part in a vise and a vise-grip on the plastic, turn a couple times and it comes right off.>>>



The cutting part of the tool is reverse "threaded", so keep that in mind when using a drill.>>>



USE CUTTING OIL! And take your time, don't build up excess heat. I didn't use a front sight fixture (used the gas tube, fingers, and constant Mk. I eyeball checking to maintain alignment) so it took about 40 minutes to have the first pin installed, which held the alignment for the 20 minutes to install the second pin.>>>



Front sight is dead-on straight, no canting or looseness. Reamer is still good for more reaming, just as sharp as when I first got it. Yes, I'd buy it again when this one wears out.

Litt anbefalt

Brownells USA Useless Handle 20.03.2017

Before you start, grab some light leather gloves. As quickly as possible, get the reamer stuck so that the handle will start to rotate without moving the reamer. Now turn the handle quickly to heat it up and then pull the handle off. Now use a tap handle and the reamer will work fine. If you don't use the glove, you will quickly get a blister because not only is the handle useless, it won't fit the human hand.

Oops! Noe gikk galt.

Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden på nytt for å fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.

Tilbake til toppen