Protects Hand & Rail From Heat & Abrasion; Easy Slide-On Installation
Molded polymer cover slides over any Picatinny handguard rail to provide a comfortable, secure grasping surface. Protects the hand from sharp rail edges and barrel heat during long shooting sessions. Molded-in knurled bands enhance your grip, especially when hand is wet, and match the Troy Modular Combat Grip to give your rifle a neat, unified appearance. No struggling to stretch the cover over the rail: simply pop up the retaining clip, slide on rail, and close the positive-locking clip to keep the cover firmly in place. Sold in 3-paks.
SPECS: Polymer, Black. 6-1⁄8" (15. 6cm) long, 17⁄16" (2.6cm) wide. 1 oz. (28.3g) weight. Sold in 3-paks.
Støpt polymerdeksel som glir over enhver Picatinny håndbeskyttelsesskinne for å gi et komfortabelt, sikkert grep. Beskytter hånden mot skarpe skinnerkanter og løpsvarme under lange skyteøkter. Støpte rillede bånd forbedrer grepet, spesielt når hånden er våt, og matcher Troy Modular Combat Grip for å gi riflen din et ryddig, enhetlig utseende. Ingen kamp for å strekke dekselet over skinnen: bare løft opp festeklemmen, skyv på skinnen, og lukk den positive-låsende klemmen for å holde dekselet sikkert på plass. Selges i 3-pakninger.
SPECS: Polymer, Svart. 6-1⁄8" (15.6cm) lang, 17⁄16" (2.6cm) bred. 1 oz. (28.3g) vekt. Selges i 3-pakninger.
Mer...
Kundevurderinger for TROY INDUSTRIES BATTLE RAIL COVER 3-PK PICATINNY POLYMER BLACK 6"
Antall vurderinger: 1
Fra brownells.com: 1
Gjennomsnittsvurdering: 2
Ok if you can get them right..(26.02.2016)
I bought this to put on the Daniel Defense Omega Rail setup that I recently installed on my Colt LE6920.
All of the videos I've watched made the installation look like a snap. It didn't go that way for me. The fit of the rail covers are *very* tight. It took a while to get them in just the right spot where the lock would push in fully. On one of them I never did get the lock to seat properly.
They do look and feel nice when they're on, but I eventually gave up and decided to take them off. That was even more difficult than pushing them on. Ended up having to us the plastic end of one of my gunsmithing hammers to tap the covers off.
I ended up going back to the snap on "ladder" style ones from Magpul.
If I try to put them on again in the future I may put a little oil on there where it meets the rails. Perhaps it would go on and off more easily.
Produktnr.: 100011035 TROY INDUSTRIES BATTLE RAIL COVER 3-PK PICATINNY POLYMER BLACK 6" Produsentnr.: SCOV-BRC-36BT-0812699017326 Støpt polymerdeksel som glir over enhver Picatinny håndbeskyttelsesskinne for å gi et komfortabelt, sikkert grep. Beskytter hånden mot skarpe skinnerkanter og løpsvarme under lange skyteøkter. Støpte rillede bånd forbedrer grepet, spesielt når hånden er våt, og matcher Troy Modular Combat Grip for å gi riflen din et ryddig, enhetlig utseende. Ingen kamp for å strekke dekselet over skinnen: bare løft opp festeklemmen, skyv på skinnen, og lukk den positive-låsende klemmen for å holde dekselet sikkert på plass. Selges i 3-pakninger.
549NOK11kr 549,00
*
Leveringstid ca. 14-21 dager. Mer enn 10 stk. på lager i USA
Støpt polymerdeksel som gir et komfortabelt, sikkert grep og beskytter hånden mot skarpe kanter og varme.
Enkel installasjon med festeklemme som sikrer dekselet på plass over enhver Picatinny håndbeskyttelsesskinne.
Selges i 3-pakninger, dekselet er 6-1⁄8" (15.6cm) langt, 17⁄16" (2.6cm) bredt, og veier 1 oz. (28.3g).
Attributes
Farge:
Black
Length:
6 in
Make:
AR-15
Material:
Polymer
Style:
Picatinny
Leveringsvekt: 0,091kgFrakthøyde: 36mmFraktbredde: 155mmFraktlengde: 221mm
UPC
: 812699017326
Elementdetaljer
Made in USA
Produktnr.: 100041474 TROY INDUSTRIES BATTLE RAIL COVER 3-PK PICATINNY POLYMER BLACK 4.4" Produsentnr.: SCOV-BRC-34BT-0812699017241 Støpt polymerdeksel som glir over enhver Picatinny håndbeskyttelsesskinne for å gi et komfortabelt, sikkert grep. Beskytter hånden mot skarpe skinnerkanter og løpsvarme under lange skyteøkter. Støpte rillede bånd forbedrer grepet, spesielt når hånden er våt, og matcher Troy Modular Combat Grip for å gi riflen din et ryddig, enhetlig utseende. Ingen kamp for å strekke dekselet over skinnen: bare løft opp festeklemmen, skyv på skinnen, og lukk den positive-låsende klemmen for å holde dekselet sikkert på plass. Selges i 3-pakninger.
549NOK3kr 549,00
*
Leveringstid ca. 14-21 dager. 3 stk. på lageret i USA
Protects Hand & Rail From Heat & Abrasion; Easy Slide-On Installation
Molded polymer cover slides over any Picatinny handguard rail to provide a comfortable, secure grasping surface. Protects the hand from sharp rail edges and barrel heat during long shooting sessions. Molded-in knurled bands enhance your grip, especially when hand is wet, and match the Troy Modular Combat Grip to give your rifle a neat, unified appearance. No struggling to stretch the cover over the rail: simply pop up the retaining clip, slide on rail, and close the positive-locking clip to keep the cover firmly in place. Sold in 3-paks.
SPECS: Polymer, Black. 6-1⁄8" (15. 6cm) long, 17⁄16" (2.6cm) wide. 1 oz. (28.3g) weight. Sold in 3-paks.
Støpt polymerdeksel som glir over enhver Picatinny håndbeskyttelsesskinne for å gi et komfortabelt, sikkert grep. Beskytter hånden mot skarpe skinnerkanter og løpsvarme under lange skyteøkter. Støpte rillede bånd forbedrer grepet, spesielt når hånden er våt, og matcher Troy Modular Combat Grip for å gi riflen din et ryddig, enhetlig utseende. Ingen kamp for å strekke dekselet over skinnen: bare løft opp festeklemmen, skyv på skinnen, og lukk den positive-låsende klemmen for å holde dekselet sikkert på plass. Selges i 3-pakninger.
SPECS: Polymer, Svart. 6-1⁄8" (15.6cm) lang, 17⁄16" (2.6cm) bred. 1 oz. (28.3g) vekt. Selges i 3-pakninger.
Mer...
Kundevurderinger for TROY INDUSTRIES BATTLE RAIL COVER 3-PK PICATINNY POLYMER BLACK 6"
Antall vurderinger: 1
Fra brownells.com: 1
Gjennomsnittsvurdering: 2
Ok if you can get them right..(26.02.2016)
I bought this to put on the Daniel Defense Omega Rail setup that I recently installed on my Colt LE6920.
All of the videos I've watched made the installation look like a snap. It didn't go that way for me. The fit of the rail covers are *very* tight. It took a while to get them in just the right spot where the lock would push in fully. On one of them I never did get the lock to seat properly.
They do look and feel nice when they're on, but I eventually gave up and decided to take them off. That was even more difficult than pushing them on. Ended up having to us the plastic end of one of my gunsmithing hammers to tap the covers off.
I ended up going back to the snap on "ladder" style ones from Magpul.
If I try to put them on again in the future I may put a little oil on there where it meets the rails. Perhaps it would go on and off more easily.