BROWNELLS
AR-15/M16 EXTRACTOR BUFFER

078000071

Stronger Base For Eliminating Extractor Bounce

Tough, dense rubber insert replaces factory buffer inside the extractor spring to prevent extractor bounce that can occur in rapid-fire conditions. Insert keeps the extractor from losing contact with casings and reducing faulty ejection of the spent casing. Sold in 10-paks.

SPECS: Rubber, black. .15" (3.8mm) long, .11" (2.8mm) diameter 10-paks.

Mer...

Sterkere base for å eliminere ekstraktorsprett

Tøff, tett gummiinnsats erstatter fabrikkbufferen inne i ekstraktorfjæren for å forhindre ekstraktorsprett som kan oppstå under hurtigskyting. Innsatsen holder ekstraktoren i kontakt med hylsene og reduserer feilaktig utkast av den brukte hylsen. Selges i 10-pakninger.

SPECS: Gummi, svart. .15" (3.8mm) lang, .11" (2.8mm) diameter 10-pakninger.

Mer...

Kundevurderinger for BROWNELLS EXTRACTOR BUFFERS, 10-PAK

Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 5

Not all older extractors have these. (25.04.2010)

Extractor bounce is an easily overlooked symtom of failure to extract. Uncle Sam uses a blue buffer, but so far, these seem to work just as well. They are easy to install, don't fall out, and they actually work pretty well for plugging the listening holes of a friends telephone if you're into such tomfoolery. One of my older AR bolts did not have a buffer and I started noticing the occasional FTE with max trim length reloads. This cured it- and did not need the donut ring.

If you're not running one, YOU'RE WRONG (08.07.2014)

This is an extractor buffer. It fits inside of the base of the extractor spring (the wider part of the spring that snaps into the cup on the extractor). This is the black version, an upgraded form of the original blue version. The blue version was designed to be used with the M16A2 rifle and the higher pressure M855 62gr ammunition (which was causing extraction problems). The blue buffer, however, did not supply enough support to the extractor spring for the shorter M4 gas system (carbine length; 7" gas tube). The carbine system exhibits faster (and some would say premature) extraction due to the shorter gas system dwell time and also higher gas port pressures. This meant multiple failures to extract in combat. The black insert was developed for the carbine system but is also compatible with the rifle length gas system. If you don't know what extractor spring you are running in your gun and you don't own a Colt or BCM, then use this as an opportunity to purchase a Wolff XP or Colt Copper-washed extractor spring and use them with these buffers (both available here on Brownells).

Put simply, they are VERY cheap insurance and there is NO REASON to not use one in any and every AR15. Use these on every gas system length (pistol, carbine, mid-length, intermediate, and rifle length).

Les 2 flere anmeldelser fra brownells.com

0 0 1 NOK

Produktnr.: 078000071
BROWNELLS EXTRACTOR BUFFERS, 10-PAK Tøff, tett gummiinnsats erstatter fabrikkbufferen inne i ekstraktorfjæren for å forhindre ekstraktorsprett som kan oppstå under hurtigskyting. Innsatsen holder ekstraktoren i kontakt med hylsene og reduserer feilaktig utkast av den brukte hylsen. Selges i 10-pakninger.

Varsle ved tilgjengelighet

Ikke tilgjengelig.

Spesifikasjoner: Make: AR-15

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Top takeaways

Tøff gummiinnsats erstatter fabrikkbufferen i ekstraktorfjæren for å forhindre ekstraktorsprett under hurtigskyting.
Holder ekstraktoren i kontakt med hylsene og reduserer feilaktig utkast av brukte hylser.
Selges i 10-pakninger; hver buffer er .15" (3.8mm) lang og .11" (2.8mm) i diameter.