Din handlekurv er tom.

Handlekurv

Hjelp og kontakt

Gratis frakt over kr 3000

100-dagers returrett

Nyhetsbrev

Salg

Over 300 000 kunder - vi takker dere!

4,93/5 "Veldig bra" (1400+ anmeldelser)

40 000+ produkter for jakt og skytesport

EGW
ANGLED BORED BUSHING WITH CARRY BEVEL

841370103379 296000066

Pre-Machined With The Proper Lockup Angle

Beveled flange looks right on melted guns. Bored at an angle to prevent barrel bind for smooth cycling. Provides a snug drop-in between barrel and bushing.

SPECS: Stainless steel. .580" (14.7mm) I.D., .70" (17.8mm) O.D.

Mer...

Forhåndsmaskinert med den riktige låsevinkelen

Fasongskåret flens ser riktig ut på smeltede våpen. Boret i en vinkel for å forhindre tønnebinding for jevn sykling. Gir en tett innpassing mellom løp og bushing.

SPECS: Rustfritt stål. .580" (14.7mm) I.D., .70" (17.8mm) O.D.

Mer...

Kundevurderinger for EGW CARRY BEVEL BUSHING, GOVT

Antall vurderinger: 11
Fra brownells.com: 11
Gjennomsnittsvurdering: 5

With Some Help From .... (13.12.2011)

a bushing wrench, the EGW bushing replaced the stock bushing without any fitting. Did touch up the edges, as they were rather sharp. The barrel fit was to say the least, spot on. Flange on front of bushing is much thicker to extend to the crown of the barrel. Nice beveled edge on flange.

Great Fit! (20.12.2012)

The bushing was for a Colt Combat Commander. It was a tight fit, but it did not require tuning. However, a bushing wrench is necessary due to the tight fit.

fit like a glove (22.02.2010)

Specs are perfect, I.D and O.D. Looks great and fits even better. Couldn't be happier Installed on a Kimber classic custom target with a better fit than the original bushing. A++++

great product (12.12.2011)

i use this bushing with great results in my shop. i use this part # a lot

Excellent (04.05.2012)

About 20 min of fitting on my Colt Govt. model tight fit. Extra thickness has made the barrel flush, Functions great, looks even better. Highly recommended.

Works as good as it looks. (15.08.2012)

This is a nice bushing. Snug fit to the slide and minimal fitting to the barrel.

Fit my RIA 1911 A1 FS perfectly (26.09.2012)

This EGW SS bushing fit my newer RIA 1911-A1 FS perfectly; tighter fit than the original RIA bushing, needed a bushing tool to help seat it, but was not too tight. Fits perfectly with the EGW long nose solid spring plug.

Quality bushing (17.07.2013)

I put this bushing on my Magnum Research 1911. It fit the slide perfectly but required minor fitting for the barrel. It's much tighter than the factory bushing and it looks great on a black gun! I highly recommend this product.

Top of the line product (18.07.2013)

I ordered this bushing and the long nose plug also for my Citadel 1911 A1. With the factory bushing the pistol would print a 3.85 inch group at 25 yards from a bench rest sand bag. I received the EGW bushing and plug yesterday, installed it and went directly to the range. The pistol now prints a 2.65 inch group at 25 yards from the bench rest.

No problems what so ever installing and perfect functioning with no fails to feed or extract.

Best bang for the buck for an accuracy upgrade.

Closer to match fit for Kimber 1911s (20.12.2014)

This is a great upgrade for slightly tighter barrel fitting on a Kimber 1911, but you may need to fit the OD to allow it to go into slide. I was able to drop it into 1 of 3 Kimbers slides that I tried. It is very tight on the one that it does go into.

Another thing I like is the fact there is no writing stamped into exterior. It is nice and clean. Ed Brown and Wilson both stamp their names on exterior of bushing.

Best 1911 bushing on this planet. (13.03.2016)

Order it now.

Smile forever.

Enough said.

Les 11 flere anmeldelser fra brownells.com

549 549 2 NOK

Produktnr.: 296000066
EGW CARRY BEVEL BUSHING, GOVT
Produsentnr.: 14212A 841370103379 Fasongskåret flens ser riktig ut på smeltede våpen. Boret i en vinkel for å forhindre tønnebinding for jevn sykling. Gir en tett innpassing mellom løp og bushing.

549 NOK 5 kr 549,00 *

Leveringstid ca. 14-21 dager.
5 stk. på lageret i USA

Spesifikasjoner: Finish: Stainless Steel Make: 1911 Modell: Government Style: Angled

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Attributes

Finish: Stainless Steel Make: 1911 Modell: Government Style: Angled Leveringsvekt: 0,005kg Frakthøyde: 20mm Fraktbredde: 76mm Fraktlengde: 122mm UPC : 841370103379

Elementdetaljer

Made in USA

Produktnr.: 296000067
EGW CARRY BEVEL BUSHING, COMMANDER
Produsentnr.: 14212C 841370103386 Fasongskåret flens ser riktig ut på smeltede våpen. Boret i en vinkel for å forhindre tønnebinding for jevn sykling. Gir en tett innpassing mellom løp og bushing.

549 NOK 4 kr 549,00 *

Leveringstid ca. 14-21 dager.
4 stk. på lageret i USA

Spesifikasjoner: Finish: Stainless Steel Make: 1911 Modell: Commander Style: Angled

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Oppdag vår ANGLED BORED BUSHING med CARRY BEVEL for 1911 Government. 🔧 Gir perfekt innpassing og forhindrer tønnebinding.

Pre-Machined With The Proper Lockup Angle

Beveled flange looks right on melted guns. Bored at an angle to prevent barrel bind for smooth cycling. Provides a snug drop-in between barrel and bushing.

SPECS: Stainless steel. .580" (14.7mm) I.D., .70" (17.8mm) O.D.

Mer...

Forhåndsmaskinert med den riktige låsevinkelen

Fasongskåret flens ser riktig ut på smeltede våpen. Boret i en vinkel for å forhindre tønnebinding for jevn sykling. Gir en tett innpassing mellom løp og bushing.

SPECS: Rustfritt stål. .580" (14.7mm) I.D., .70" (17.8mm) O.D.

Mer...

Kundevurderinger for EGW CARRY BEVEL BUSHING, GOVT

Antall vurderinger: 11
Fra brownells.com: 11
Gjennomsnittsvurdering: 5

With Some Help From .... (13.12.2011)

Great Fit! (20.12.2012)

The bushing was for a Colt Combat Commander. It was a tight fit, but it did not require tuning. However, a bushing wrench is necessary due to the tight fit.

fit like a glove (22.02.2010)

Specs are perfect, I.D and O.D. Looks great and fits even better. Couldn't be happier Installed on a Kimber classic custom target with a better fit than the original bushing. A++++

great product (12.12.2011)

i use this bushing with great results in my shop. i use this part # a lot

Excellent (04.05.2012)

About 20 min of fitting on my Colt Govt. model tight fit. Extra thickness has made the barrel flush, Functions great, looks even better. Highly recommended.

Works as good as it looks. (15.08.2012)

This is a nice bushing. Snug fit to the slide and minimal fitting to the barrel.

Fit my RIA 1911 A1 FS perfectly (26.09.2012)