Factory Specified Size Measures M16/AR-15 Maximum Headspace
Made to the Colt factory's special dimensions for M16/AR-15 rifles. It measures the maximum factory acceptable headspace; an essential check on guns that have seen extensive service or have been rebarreled.
SPECS: Hardened and ground steel. 1.65" (4.2cm) overall (this is NOT the "headspace" dimension). .3655" (9.3mm) diameter.
Laget etter Colts fabrikks spesialdimensjoner for M16/AR-15 rifler. Den måler maksimalt akseptabelt headspace i henhold til fabrikken; en essensiell kontroll for våpen som har vært mye i bruk eller har blitt ombygget med ny pipe.
SPECS: Herdet og slipt stål. 1.65" (4.2cm) totalt (dette er IKKE "headspace"-dimensjonen). .3655" (9.3mm) diameter.
Mer...
Kundevurderinger for BROWNELLS COLT FIELD 5.56X45MM HEADSPACE GAUGE 1.4736
Antall vurderinger: 3
Fra brownells.com: 3
Gjennomsnittsvurdering: 5
It works(21.01.2011)
Yes, it works! Take note before use, don't slam it into battery as it can damage the gun and/or guage.
A must have for the AR-15 owner(16.07.2012)
I bought this gauge to know without a doubt that my rifle would be safe to fire and free of any factory defects in headspace. This gauge is also a must have for any AR-15 shooter who wants to replace a bolt or buy a different bolt than what was originally supplied by the manufacturer of the upper receiver.
Does its job, extra security(18.03.2014)
I purchased this to verify the headspace in my AR build did not exceed spec as I built the upper from individual parts. It checked out fine and shot fine as I figured it would. However, 22 bucks is a small amount to verify safety. Sure, you could just shoot it and make sure the cases arn't bulging or the primer backing out. Still worth it to me and it was nice to verify everything was indeed mil-spec. This should be a do it yourself job for anyone that can successfully build their own AR, just a matter of stripping the bolt.
Produktnr.: 319418033 BROWNELLS COLT FIELD 5.56X45MM HEADSPACE GAUGE 1.4736757253992421 Laget etter Colts fabrikks spesialdimensjoner for M16/AR-15 rifler. Den måler maksimalt akseptabelt headspace i henhold til fabrikken; en essensiell kontroll for våpen som har vært mye i bruk eller har blitt ombygget med ny pipe.
799NOK0kr 799,00
*
Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.
Spesifikasjoner:Kaliber: 5.56 mm NATOStyle: Field Gauge
Factory Specified Size Measures M16/AR-15 Maximum Headspace
Made to the Colt factory's special dimensions for M16/AR-15 rifles. It measures the maximum factory acceptable headspace; an essential check on guns that have seen extensive service or have been rebarreled.
SPECS: Hardened and ground steel. 1.65" (4.2cm) overall (this is NOT the "headspace" dimension). .3655" (9.3mm) diameter.
Laget etter Colts fabrikks spesialdimensjoner for M16/AR-15 rifler. Den måler maksimalt akseptabelt headspace i henhold til fabrikken; en essensiell kontroll for våpen som har vært mye i bruk eller har blitt ombygget med ny pipe.
SPECS: Herdet og slipt stål. 1.65" (4.2cm) totalt (dette er IKKE "headspace"-dimensjonen). .3655" (9.3mm) diameter.
Mer...
Kundevurderinger for BROWNELLS COLT FIELD 5.56X45MM HEADSPACE GAUGE 1.4736
Antall vurderinger: 3
Fra brownells.com: 3
Gjennomsnittsvurdering: 5
It works(21.01.2011)
Yes, it works! Take note before use, don't slam it into battery as it can damage the gun and/or guage.
A must have for the AR-15 owner(16.07.2012)
I bought this gauge to know without a doubt that my rifle would be safe to fire and free of any factory defects in headspace. This gauge is also a must have for any AR-15 shooter who wants to replace a bolt or buy a different bolt than what was originally supplied by the manufacturer of the upper receiver.
Does its job, extra security(18.03.2014)
I purchased this to verify the headspace in my AR build did not exceed spec as I built the upper from individual parts. It checked out fine and shot fine as I figured it would. However, 22 bucks is a small amount to verify safety. Sure, you could just shoot it and make sure the cases arn't bulging or the primer backing out. Still worth it to me and it was nice to verify everything was indeed mil-spec. This should be a do it yourself job for anyone that can successfully build their own AR, just a matter of stripping the bolt.