No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Mer...
Ingen dreiebenk nødvendig, ingen grunn til å fjerne løpet fra rammen
Super skånsom vinkel som for tiden brukes av Ruger på deres .38/.357 DA våpen. Hvis du skal sette tilbake en Ruger-løp eller bare ønsker å duplisere denne vinkelen på et annet løp, bruk denne kutteren. Du KAN IKKE bruke 18° eller 11° kuttere på en 5° hals uten å overskride maksimal halsdiameter eller lage en sammensatt vinkel.
Mer...
Kundevurderinger for BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 1
My 45 cal, 5 Degree Did Not Cut.(15.05.2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16.11.2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.
Produktnr.: 080486500 BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER050806009752 Super skånsom vinkel som for tiden brukes av Ruger på deres .38/.357 DA våpen. Hvis du skal sette tilbake en Ruger-løp eller bare ønsker å duplisere denne vinkelen på et annet løp, bruk denne kutteren. Du KAN IKKE bruke 18° eller 11° kuttere på en 5° hals uten å overskride maksimal halsdiameter eller lage en sammensatt vinkel.
899NOK1kr 899,00
*
Leveringstid ca. 14-21 dager. 1 stk. på lageret i USA
Produktnr.: 080486100 BROWNELLS 5 CHAMFER CUTTER FOR .38 CALIBER050806009707 Super skånsom vinkel som for tiden brukes av Ruger på deres .38/.357 DA våpen. Hvis du skal sette tilbake en Ruger-løp eller bare ønsker å duplisere denne vinkelen på et annet løp, bruk denne kutteren. Du KAN IKKE bruke 18° eller 11° kuttere på en 5° hals uten å overskride maksimal halsdiameter eller lage en sammensatt vinkel.
999NOK3kr 999,00
*
Leveringstid ca. 14-21 dager. 3 stk. på lageret i USA
No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Mer...
Ingen dreiebenk nødvendig, ingen grunn til å fjerne løpet fra rammen
Super skånsom vinkel som for tiden brukes av Ruger på deres .38/.357 DA våpen. Hvis du skal sette tilbake en Ruger-løp eller bare ønsker å duplisere denne vinkelen på et annet løp, bruk denne kutteren. Du KAN IKKE bruke 18° eller 11° kuttere på en 5° hals uten å overskride maksimal halsdiameter eller lage en sammensatt vinkel.
Mer...
Kundevurderinger for BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 1
My 45 cal, 5 Degree Did Not Cut.(15.05.2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16.11.2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.