A damaged or poorly-cut muzzle can really hurt accuracy; sharp edges on revolver cylinder chamber mouths can cause rounds to hang up going into the cylinder - a real problem when using speedloaders. Cure both problems with this cutter.
SPECS: Cutter - 3-1/4" (8.25cm) long (except .17 caliber cutter - 2-3/8" (6cm) long). 1/2" (12.7mm) or 5/8" (15.8mm) diameter.
Mer...
En skadet eller dårlig kuttet munning kan virkelig skade presisjonen; skarpe kanter på revolverens kammermunninger kan føre til at patroner henger seg opp når de settes inn i tønnen - et reelt problem ved bruk av hurtigladere. Løs begge problemer med denne kutteren.
SPECS: Kutter - 3-1/4" (8.25cm) lang (unntatt .17 kaliber kutter - 2-3/8" (6cm) lang). 1/2" (12.7mm) eller 5/8" (15.8mm) diameter.
Mer...
Kundevurderinger for BROWNELLS 45 1/2" CHAMFERING CUTTER ONLY
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 3
pilot hole too large(05.11.2016)
The pilot hole is too large for the .17 cal pilots. The pilot must be shimmed with wraps of .001" stock until proper fit is attained. Only then can a nice cut be made. There is apparently a miscommunication between the pilot and cutter maker. My cutters and pilots for calibers 22 and up all fit together tightly.
45°, 5/8" Chamfering Cutter (04.06.2016)
Used this with Brownells .45 BBL. Revolver Muzzle Brass Pilot (#080-944-450) to re-crown my S&W 625PC. The brass pilot measured .4405" diameter which was a good fit for my bore (.443") diameter. The Cutter's diameter (5/8") was a good match on the guns I used it on (S&W 625, 627, & 686). The last one I used it on left chatter marks/ripples. Not sure why as it cut the others smoothly. (Hope it's not getting dull already?) Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.
Produktnr.: 080588454 BROWNELLS 45 1/2" CHAMFERING CUTTER ONLY050806017252 En skadet eller dårlig kuttet munning kan virkelig skade presisjonen; skarpe kanter på revolverens kammermunninger kan føre til at patroner henger seg opp når de settes inn i tønnen - et reelt problem ved bruk av hurtigladere. Løs begge problemer med denne kutteren.
1349NOK13kr 1 349,00
*
Leveringstid ca. 14-21 dager. Mer enn 10 stk. på lager i USA
Produktnr.: 080588453 BROWNELLS 45 17 CALIBER 1/2" CHAMFER CUTTER ONLY050806017245 En skadet eller dårlig kuttet munning kan virkelig skade presisjonen; skarpe kanter på revolverens kammermunninger kan føre til at patroner henger seg opp når de settes inn i tønnen - et reelt problem ved bruk av hurtigladere. Løs begge problemer med denne kutteren.
1399NOK7kr 1 399,00
*
Leveringstid ca. 14-21 dager. 7 stk. på lageret i USA
Produktnr.: 080588625 BROWNELLS 45 5/8" CHAMFERING CUTTER ONLY050806017269 En skadet eller dårlig kuttet munning kan virkelig skade presisjonen; skarpe kanter på revolverens kammermunninger kan føre til at patroner henger seg opp når de settes inn i tønnen - et reelt problem ved bruk av hurtigladere. Løs begge problemer med denne kutteren.
1299NOK0kr 1 299,00
*
Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.
A damaged or poorly-cut muzzle can really hurt accuracy; sharp edges on revolver cylinder chamber mouths can cause rounds to hang up going into the cylinder - a real problem when using speedloaders. Cure both problems with this cutter.
SPECS: Cutter - 3-1/4" (8.25cm) long (except .17 caliber cutter - 2-3/8" (6cm) long). 1/2" (12.7mm) or 5/8" (15.8mm) diameter.
Mer...
En skadet eller dårlig kuttet munning kan virkelig skade presisjonen; skarpe kanter på revolverens kammermunninger kan føre til at patroner henger seg opp når de settes inn i tønnen - et reelt problem ved bruk av hurtigladere. Løs begge problemer med denne kutteren.
SPECS: Kutter - 3-1/4" (8.25cm) lang (unntatt .17 kaliber kutter - 2-3/8" (6cm) lang). 1/2" (12.7mm) eller 5/8" (15.8mm) diameter.
Mer...
Kundevurderinger for BROWNELLS 45 1/2" CHAMFERING CUTTER ONLY
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 3
pilot hole too large(05.11.2016)
The pilot hole is too large for the .17 cal pilots. The pilot must be shimmed with wraps of .001" stock until proper fit is attained. Only then can a nice cut be made. There is apparently a miscommunication between the pilot and cutter maker. My cutters and pilots for calibers 22 and up all fit together tightly.
45°, 5/8" Chamfering Cutter (04.06.2016)
Used this with Brownells .45 BBL. Revolver Muzzle Brass Pilot (#080-944-450) to re-crown my S&W 625PC. The brass pilot measured .4405" diameter which was a good fit for my bore (.443") diameter. The Cutter's diameter (5/8") was a good match on the guns I used it on (S&W 625, 627, & 686). The last one I used it on left chatter marks/ripples. Not sure why as it cut the others smoothly. (Hope it's not getting dull already?) Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.