Each and every part is U.S.-made, high-quality and guaranteed to fit and function just like the factory part.
SPECS: Fits 1911 Auto. All parts carbon steel. (B) indicates blued finish, (S) indicates stainless steel.
Deler Laget I USA For 1911 Auto Pistol
Hver eneste del er laget i USA, av hĂžy kvalitet og garantert Ă„ passe og fungere akkurat som originaldelen.
SPESIFIKASJONER: Passer til 1911 Auto. Alle deler er laget av karbonstÄl. (B) indikerer blÄnert finish, (S) indikerer rustfritt stÄl.
Attributes
Finish:Blued
Hand:Right
Modell:Commander,Government,Officers
Style:Thumb
VÄpentype:1911
Leveringsvekt:0,009kg
FrakthĂžyde:4mm
Fraktbredde:80mm
Fraktlengde:122mm
Elementdetaljer
Made in USA
US eksport klassifisering: 0A501.x
Kundeanmeldelser
Kundevurderinger (11)
2,3 / 5
Litt anbefalt
Not the best 28.07.2018
The item I got had a very long arm that needed more than a little trimming, just to fit in the receiver. The receiver is an ATI - maybe suspect - but several old Colt safeties fit (and work) just fine.
Well folks, by the time I carefully fit the LENGTH of the arm, it became evident that the width of the arm (top to bottom) was insufficient to actually do anything. That is to say, the little nub at the end of the arm didn't swing down enough to intersect the back of the trigger bow. Bummer.
My first thought was that the hooks that intersect the top of the mainspring housing need adjustment to allow the safety to swing further. But this turned out not to be the case. Instead, after close comparison with the ATI grip safety and the old Colt grip safeties, its quite evident that this safety quite a bit "out of spec". Its like... its bent? Cant unbend it, but I can weld up the arm and recut the entire piece. However, if I wanted to resort to that, I could have just done that to the original (which did block the hammer somewhat, but allowed too much rearward travel, allowing the sear to partially disengage... nice, right from ATI that way, but heck its a $300 1911....!!!)
Sorry, this one's a dud.
Ikke anbefalt
Avoid 18.04.2018
The finish was better than expected, but when installed the arm did not contact the trigger stirrup. When compared to a surplus GI grip safety, the trigger block arm was significantly higher on the Masen part. Called technical support for advice and was told I should've bought a better quality grip safety.
Ikke anbefalt
Avoid 14.01.2017
The spring detent notch on front of safety does not have enough material below it to prevent the safety plunger from dropping below the front lower edge of the safety casting and locking up the safety.
Anbefalt med reservasjoner
Works 22.08.2015
Functions as a safety but does not have a good finish and casting edges. Can't beat the cost though.
Litt anbefalt
Is the low price worth your time? 29.01.2015
Buy if you're on a budget and have skills. Avoid if "drop-in" were the first words in your query. I'm applying this part to a new SS receiver and immediately noted the body of the safety does not sit flush against the receiver body. Two aspects to this; the grip safety pin is not exactly perpendicular to the body of the safety and casting imperfections on the inside surface. This part requires significant fitting/stoning/blasting (and time) to adequately fit, function and look pretty. All this said, economizing on this part and a JTM grip safety allowed me to afford other, more desired, parts for this build. Two stars for overall value but falls short of even parts-bucket quality/fit/function.
Ikke anbefalt
Poor Quality 30.10.2012
Purchased this Grip Safety to replace a cosmetically worn Series 80 grip safety. Part is for Series 70 only, but can be filed to work in Series 80 gun.
Part is extremely poorly finished - large cast line down the center that can be felt quite easily, and the black/blue finish is finely scratched everywhere.
Stay away from Masen parts - they are garbage.
Anbefalt
great bang for the buck 11.04.2012
replaced a worn remington r1 grip safety. took all five minutes to replace. above average finish as you can see in the picture.
Ikke anbefalt
Poor Quality 27.11.2011
Uneven cut, uneven grind finish, purchased a cheap part to modify. Casting was full of holes. Not evenly ground
Litt anbefalt
Horrible finish 16.08.2011
Unless your going to re-blue the part, don't bother. Their idea of blued finish looks like a rust brown. I was refinishing the gun anyway and bluing it but for a drop in, you would be seriously disappointed in the finish. Heavy casting and grind marks in the one I got too. I ending up bead blasting and sanding the finish smooth before I blued it. More effort than what I was looking for.
Anbefalt
Decent Gear 17.01.2011
Used as a replacement on a basic 1911, this did the job without much hassle. It's also inexpensive enough that if you have to do any work on it yourself and you do screw it up, you're not out much money. Installed pretty easily and was easy to work with. Decent piece of gear. - Be sure to test-fit parts before installing them, as this won't work with some modern rounded hammers that meant for beavertails that have an indention/hammer recess cut. This is meant for GI-style hammer spurs. Make sure you test fit it before you start putting pins in, or you'll have to fight to disassemble it.
Anbefalt
good product 27.07.2010
plenty of meat in the trigger bar, good fit, finish.
Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden pÄ nytt for Ä fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.
Oppgrader din 1911 med John Masen Thumb Safety đ. HĂžy kvalitet, perfekt passform og funksjon. Ideell for Government, Commander og Officers.
ErklÊring om kontroll av destinasjon: Disse artiklene er underlagt kontroll av den amerikanske regjering og er kun godkjent for eksport til destinasjonslandet, for anvendelse av den endelige mottager eller sluttbruker(ene), heri identifisert. De skal ikke videreselges, overfÞres eller pÄ annen mÄte avhendes til et annet land eller til en annen person enn den godkjente mottakeren eller sluttbrukeren(ene), enten i sin opprinnelige form eller etter innlemmelse i andre artikler, uten fÞrst Ä fÄ godkjenning fra den amerikanske regjering eller dersom godkjennelse fÞlger av amerikanske lover eller forskrifter.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
ErklÊring om kontroll av destinasjon: Disse artiklene er underlagt kontroll av den amerikanske regjering og er kun godkjent for eksport til destinasjonslandet, for anvendelse av den endelige mottager eller sluttbruker(ene), heri identifisert. De skal ikke videreselges, overfÞres eller pÄ annen mÄte avhendes til et annet land eller til en annen person enn den godkjente mottakeren eller sluttbrukeren(ene), enten i sin opprinnelige form eller etter innlemmelse i andre artikler, uten fÞrst Ä fÄ godkjenning fra den amerikanske regjering eller dersom godkjennelse fÞlger av amerikanske lover eller forskrifter.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
1911 Stock Bushings er laget for 1911 Government-modellen og kommer i sett pÄ 4 hylser.
Tilgjengelig i bÄde standard blÄtt stÄl og rustfritt stÄl (S/S) for en passende finish pÄ vÄpenet ditt.
Designet for Ä erstatte strippede hylser nÄr du fjerner grepene eller rammehylsene for vedlikehold eller polering.
Klar til installasjon med fullstendig ferdige deler som gir en skarp og ren avtrekkerfĂžlelse.
Hammeren har en lavmasses oval spore som reduserer lÄsetiden og innsnevrede sider som reduserer friksjon.
MIM-stÞpt 4340 stÄl, herdet til Rc 47-52, med matt svart finish for Þkt holdbarhet.
Forhindrer at rammen blir skjev ved bruk av tilpassede Delrin-innsatser som matcher revolverrammens konturer.
Utskiftbare innsatser tillater justering for Ä kompensere for variasjoner i individuelle vÄpen.
StÄlhÄndtak med aluminiumshode og Delrin-innsats, total lengde pÄ 39 cm og veier 0.79 kg uten innsats.
MuliggjĂžr raskere og enklere magasinbytter med en forlenget knapp som gir enklere tommelfeste.
Kompakt nok til Ă„ passe i bĂŠrehylstre uten Ă„ henge seg opp i klĂŠr, med en positiv intern stopp som forhindrer overtrykking.
Maskinert fra stangstÄl, varmebehandlet for holdbarhet, og tilgjengelig i blÄtt finish eller rustfritt stÄl.
1911 Standard Stock Screws er laget for Ä erstatte standardskruer pÄ 1911 Government-modellen nÄr grepene fjernes.
Settet inkluderer fire blÄlagte skruer, designet for Ä passe bÄde rustfritt stÄl og nikkelbelagte vÄpen.
Skruene har spesifikasjonen .150"-50 gjenger og er tilgjengelige i bÄde blÄtt stÄl og rustfritt stÄl (S/S).