Traditional & Increased-Capacity Magazines For 1911 Colts, Copies & Compacts
Robust, high-quality U.S. made magazines in blued carbon steel and stainless steel for 1911 Auto pistols chambered in a variety of calibers. Choose from round or flat steel followers, both designed to give positive last-round feeding with all bullet types, including wadcutters. Safety orange nylon follower is concave to hold an additional round. Three floorplate configurations available: Welded – Flat, steel plate permanently welded to magazine body, with screw holes to accept Metalform Bumper Pads.
SPECS: Blued carbon steel (Blue) or natural-finish stainless steel (Stnls). Approximately 5" (12.7cm) long. Followers – Stainless steel, natural silver or black finish, flat or round contour. Some magazines have concave safety orange nylon follower.
Mer...
Tradisjonelle og høykapasitetsmagasiner for 1911 Colts, kopier og kompakter
Robuste, høykvalitets amerikanskproduserte magasiner i blått karbonstål og rustfritt stål for 1911 Auto pistoler kamret for et utvalg av kaliber. Velg mellom runde eller flate stålfølgere, begge designet for å gi positiv mating av siste skudd med alle kuletyper, inkludert wadcutters. Sikkerhetsfølger i oransje nylon er konkav for å holde en ekstra patron. Tre typer bunnplater tilgjengelig: Sveiset – Flat, stålplate permanent sveiset til magasinkroppen, med skruehull for å feste Metalform støtdempere.
SPECS: Blått karbonstål (Blå) eller rustfritt stål med naturlig finish (Rustfritt). Omtrent 5" (12.7cm) lang. Følgere – Rustfritt stål, naturlig sølv eller svart finish, flat eller rund kontur. Noen magasiner har konkav sikkerhetsfølger i oransje nylon.
Mer...
Kundevurderinger for METALFORM .45 GOVT/COMM BLUE 7 RD. ROUND FOLLOWER W/WELDED BASE
Antall vurderinger: 10
Fra brownells.com: 10
Gjennomsnittsvurdering: 3,4
promising but no(18.01.2018)
on the positive side, this is one of very few magazines on the market with hybrid feed lips. Which means it feeds as 1911 was designed to feed, or close to it. And, it's a flush fitting 8rd magazine, which is nice.
On the negative side, 1) it consistently fails limp wristing test through the top 3 rounds and 2) it overrides the mag catch, which is not a trivial failure. It remains to be seen if this can be remedied, but as it comes from the factory this magazine is unfortunately unacceptable.
Solid performer, simple(29.01.2010)
Been using these mags for 7 years now. No rust yet. Follower design engages slide stop every time I run empty, and the feed lips are holding. If you reload semi-wadcutters, load up a few dummy rounds first to get the case OAL correct to ensure flawless magazine function. The only negative I can think of is that the great follower design is tricky to remove for magazine cleaning and inspection.
100%(05.03.2011)
Springfield provided these mags with all three 1911s I own. I have about 20 of them and not one has ever failed me. They may not look like they are made of quality but trust me, they will work!
Great quality - Great price!(13.02.2012)
Excellent value. So dependable that I have been using in my carry gun for 15+ years. Suggest if used for competition that rubber bumpers be used; any magazine can only withstand so many speed change drops to the ground. Disassembly not difficult with a short piece of wood ruler (to depress follower) and small punch to hold spring. Round follower works exceptionally well.
Breakage/wad feeding problems(25.12.2012)
Had floorplate fall off, MF replaced with one that wouldn't feed 190 gr lee wheelweight cast semi-wad. Other mag worked fine.
Solid and Simple(18.08.2015)
I purchased three of these and so far I am happy. They work great in my 1911. Feeding and performance is as good as my 47Ds, CMC Power mags and CheckMate 7rnd hybrid feed-lip w/ dimpled follower. The rounded follower design helps to mimic a round below the last round and will ensure positive ejection should your extractor fail. Removal of the follower for magazine cleaning takes a little more effort. Overall, I think it is a great design and I have no complaints.
No HP or SWC(26.11.2015)
i bought 6 of these earlier this year, as arrived none would feed high performance .45-185gr-HP or .45-185gr-SW. when i went to open the feed lips to decrease the feed angle, the feed lips cracked on 3 of the 6, making them useless. buy something else.
Worked well for a long time(24.03.2016)
Have used these mags a lot. Have only had spring issues with one. After countless speed and tac reloads finally cracked the welds and bent the bases on several of these mags. Other than that for the price they have been great mags and have carried them for duty for many years.
Sub part welds(06.07.2016)
I received two of these mags for use in my 1911 and BOTH of the base plates broke off in the same manner. I had seven round in the mag and when I tried to chamber a round, the base plate fell off, along with the spring, follower and the rest of the ammo. I will never buy these again.
Good product(13.03.2017)
I bought 2 of these mags for my Series 70 Colt. Fit was perfect and worked flawlessly. Good product. Better then my Colt Mags. I like the SS followers.
Produktnr.: 620045001 METALFORM .45 GOVT/COMM BLUE 7 RD. ROUND FOLLOWER W/WELDED BASE Produsentnr.: 45.297 Robuste, høykvalitets amerikanskproduserte magasiner i blått karbonstål og rustfritt stål for 1911 Auto pistoler kamret for et utvalg av kaliber. Velg mellom runde eller flate stålfølgere, begge designet for å gi positiv mating av siste skudd med alle kuletyper, inkludert wadcutters. Sikkerhetsfølger i oransje nylon er konkav for å holde en ekstra patron. Tre typer bunnplater tilgjengelig: Sveiset – Flat, stålplate permanent sveiset til magasinkroppen, med skruehull for å feste Metalform støtdempere.
699NOK81kr 699,00
*
Leveringstid ca. 14-21 dager. Mer enn 10 stk. på lager i USA
Robuste magasiner laget av blått karbonstål eller rustfritt stål for 1911 Auto pistoler, tilgjengelig i flere kaliber.
Tilgjengelige følgere inkluderer runde eller flate stålfølgere, og konkave sikkerhetsfølgere i oransje nylon for ekstra patron.
Tre typer bunnplater: sveiset flat stålplate, med skruehull for å feste Metalform støtdempere.
Attributes
Cartridge:
45 Auto (ACP)
Finish:
Black
Kapasitet:
7-Round
Make:
1911
Material:
Steel
Modell:
Commander,Government
Leveringsvekt: 0,023kgFrakthøyde: 13mmFraktbredde: 69mmFraktlengde: 152mm
Elementdetaljer
Made in USA
US eksport klassifisering: 0A501.x
Erklæring om kontroll av destinasjon: Disse artiklene er underlagt kontroll av den amerikanske regjering og er kun godkjent for eksport til destinasjonslandet, for anvendelse av den endelige mottager eller sluttbruker(ene), heri identifisert. De skal ikke videreselges, overføres eller på annen måte avhendes til et annet land eller til en annen person enn den godkjente mottakeren eller sluttbrukeren(ene), enten i sin opprinnelige form eller etter innlemmelse i andre artikler, uten først å få godkjenning fra den amerikanske regjering eller dersom godkjennelse følger av amerikanske lover eller forskrifter.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Produktnr.: 620045083 METALFORM .45 GOVT/COMM BLUE 8 RD. FLAT FOLLOWER W/WELDED BASE Produsentnr.: 45-298 Robuste, høykvalitets amerikanskproduserte magasiner i blått karbonstål og rustfritt stål for 1911 Auto pistoler kamret for et utvalg av kaliber. Velg mellom runde eller flate stålfølgere, begge designet for å gi positiv mating av siste skudd med alle kuletyper, inkludert wadcutters. Sikkerhetsfølger i oransje nylon er konkav for å holde en ekstra patron. Tre typer bunnplater tilgjengelig: Sveiset – Flat, stålplate permanent sveiset til magasinkroppen, med skruehull for å feste Metalform støtdempere.
549NOK43kr 549,00
*
Leveringstid ca. 14-21 dager. Mer enn 10 stk. på lager i USA
Produktnr.: 620045084 METALFORM .45 GOVT/COMM S/S 8 RD. FLAT FOLLOWER W/WELDED BASE Produsentnr.: 45-798 Robuste, høykvalitets amerikanskproduserte magasiner i blått karbonstål og rustfritt stål for 1911 Auto pistoler kamret for et utvalg av kaliber. Velg mellom runde eller flate stålfølgere, begge designet for å gi positiv mating av siste skudd med alle kuletyper, inkludert wadcutters. Sikkerhetsfølger i oransje nylon er konkav for å holde en ekstra patron. Tre typer bunnplater tilgjengelig: Sveiset – Flat, stålplate permanent sveiset til magasinkroppen, med skruehull for å feste Metalform støtdempere.
699NOK38kr 699,00
*
Leveringstid ca. 14-21 dager. Mer enn 10 stk. på lager i USA
Produktnr.: 620045002 METALFORM .45 GOVT/COMM S/S 7 RD. ROUND FOLLOWER W/WELDED BASE Produsentnr.: 45.797 Robuste, høykvalitets amerikanskproduserte magasiner i blått karbonstål og rustfritt stål for 1911 Auto pistoler kamret for et utvalg av kaliber. Velg mellom runde eller flate stålfølgere, begge designet for å gi positiv mating av siste skudd med alle kuletyper, inkludert wadcutters. Sikkerhetsfølger i oransje nylon er konkav for å holde en ekstra patron. Tre typer bunnplater tilgjengelig: Sveiset – Flat, stålplate permanent sveiset til magasinkroppen, med skruehull for å feste Metalform støtdempere.
699NOK0kr 699,00
*
Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.
Traditional & Increased-Capacity Magazines For 1911 Colts, Copies & Compacts
Robust, high-quality U.S. made magazines in blued carbon steel and stainless steel for 1911 Auto pistols chambered in a variety of calibers. Choose from round or flat steel followers, both designed to give positive last-round feeding with all bullet types, including wadcutters. Safety orange nylon follower is concave to hold an additional round. Three floorplate configurations available: Welded – Flat, steel plate permanently welded to magazine body, with screw holes to accept Metalform Bumper Pads.
SPECS: Blued carbon steel (Blue) or natural-finish stainless steel (Stnls). Approximately 5" (12.7cm) long. Followers – Stainless steel, natural silver or black finish, flat or round contour. Some magazines have concave safety orange nylon follower.
Mer...
Tradisjonelle og høykapasitetsmagasiner for 1911 Colts, kopier og kompakter
Robuste, høykvalitets amerikanskproduserte magasiner i blått karbonstål og rustfritt stål for 1911 Auto pistoler kamret for et utvalg av kaliber. Velg mellom runde eller flate stålfølgere, begge designet for å gi positiv mating av siste skudd med alle kuletyper, inkludert wadcutters. Sikkerhetsfølger i oransje nylon er konkav for å holde en ekstra patron. Tre typer bunnplater tilgjengelig: Sveiset – Flat, stålplate permanent sveiset til magasinkroppen, med skruehull for å feste Metalform støtdempere.
SPECS: Blått karbonstål (Blå) eller rustfritt stål med naturlig finish (Rustfritt). Omtrent 5" (12.7cm) lang. Følgere – Rustfritt stål, naturlig sølv eller svart finish, flat eller rund kontur. Noen magasiner har konkav sikkerhetsfølger i oransje nylon.
Mer...
Kundevurderinger for METALFORM .45 GOVT/COMM BLUE 7 RD. ROUND FOLLOWER W/WELDED BASE
Antall vurderinger: 10
Fra brownells.com: 10
Gjennomsnittsvurdering: 3,4
promising but no(18.01.2018)
on the positive side, this is one of very few magazines on the market with hybrid feed lips. Which means it feeds as 1911 was designed to feed, or close to it. And, it's a flush fitting 8rd magazine, which is nice.
On the negative side, 1) it consistently fails limp wristing test through the top 3 rounds and 2) it overrides the mag catch, which is not a trivial failure. It remains to be seen if this can be remedied, but as it comes from the factory this magazine is unfortunately unacceptable.
Solid performer, simple(29.01.2010)
Been using these mags for 7 years now. No rust yet. Follower design engages slide stop every time I run empty, and the feed lips are holding. If you reload semi-wadcutters, load up a few dummy rounds first to get the case OAL correct to ensure flawless magazine function. The only negative I can think of is that the great follower design is tricky to remove for magazine cleaning and inspection.
100%(05.03.2011)
Springfield provided these mags with all three 1911s I own. I have about 20 of them and not one has ever failed me. They may not look like they are made of quality but trust me, they will work!
Great quality - Great price!(13.02.2012)
Excellent value. So dependable that I have been using in my carry gun for 15+ years. Suggest if used for competition that rubber bumpers be used; any magazine can only withstand so many speed change drops to the ground. Disassembly not difficult with a short piece of wood ruler (to depress follower) and small punch to hold spring. Round follower works exceptionally well.
Breakage/wad feeding problems(25.12.2012)
Had floorplate fall off, MF replaced with one that wouldn't feed 190 gr lee wheelweight cast semi-wad. Other mag worked fine.
Solid and Simple(18.08.2015)
I purchased three of these and so far I am happy. They work great in my 1911. Feeding and performance is as good as my 47Ds, CMC Power mags and CheckMate 7rnd hybrid feed-lip w/ dimpled follower. The rounded follower design helps to mimic a round below the last round and will ensure positive ejection should your extractor fail. Removal of the follower for magazine cleaning takes a little more effort. Overall, I think it is a great design and I have no complaints.
No HP or SWC(26.11.2015)
i bought 6 of these earlier this year, as arrived none would feed high performance .45-185gr-HP or .45-185gr-SW. when i went to open the feed lips to decrease the feed angle, the feed lips cracked on 3 of the 6, making them useless. buy something else.
Worked well for a long time(24.03.2016)
Have used these mags a lot. Have only had spring issues with one. After countless speed and tac reloads finally cracked the welds and bent the bases on several of these mags. Other than that for the price they have been great mags and have carried them for duty for many years.
Sub part welds(06.07.2016)
I received two of these mags for use in my 1911 and BOTH of the base plates broke off in the same manner. I had seven round in the mag and when I tried to chamber a round, the base plate fell off, along with the spring, follower and the rest of the ammo. I will never buy these again.
Good product(13.03.2017)
I bought 2 of these mags for my Series 70 Colt. Fit was perfect and worked flawlessly. Good product. Better then my Colt Mags. I like the SS followers.