Attributes
- Finish: Silver
- Material: Aluminum
- Våpentype: Universal Rifles
- Leveringsvekt: 0,249kg
- Frakthøyde: 58mm
- Fraktbredde: 61mm
- Fraktlengde: 160mm
Produktnr.: 352150100
Produsentnr.: 575S
Treveis justeringer for perfekt tilpasning av våpenet, høyere poengsum og forbedret skytekomfort. Baseplaten monteres på våpenet, din pute monteres på puteplaten, og den gjengede røret gir totalt 1-1/8" inn/ut justering. Gjør hele omdreininger eller stopp rotasjonen hvor som helst i 360° og lås med skruene med sekskanthode. Spaltet toppplate tillater 1½" vertikal justering. Sett en Breako Recoil Reducer inn i røret for en pen, kompakt installasjon. Kombiner med Gracos justerbare Comb Hardware for å lage din egen "Try Stock".STANDARD ADJUSTABLE BUTT PLATE fra GRACO CORP gir deg muligheten til å tilpasse lengde, fall og rotasjon for en perfekt passform til ditt våpen. Dette produktet er ideelt for å forbedre skytekomforten og oppnå høyere poengsummer.
Med treveis justeringer for perfekt tilpasning, kan baseplaten monteres på våpenet ditt, mens din polstring monteres på pad-platen. Den gjengede røret gir totalt 1-1/8" justering inn/ut. Du kan gjøre full omdreining eller stoppe rotasjonen hvor som helst i 360° og låse med sokkelskruene. Den sporformede toppplaten tillater 1½" vertikal justering. Sett inn en Breako Recoil Reducer i røret for en ryddig og kompakt installasjon. Kombiner med Graco's Adjustable Comb Hardware for å lage din egen "Try Stock".
Boyd's SS Evolution 10/22 stock 17.08.2016
I wanted to make the Boyd's ss Evolution stock fit me better. I use it for sage rats and after a day of shooting my neck would start hurting. This adjusts down about 3/4" and twists out out which was perfect to raise the comb of the stock and fit my shoulder. A few mods were needed like drilling holes. I have not shaped it to the stock yet. However, once I do I will duracoat it to match the receiver. I would buy another once I fit this one.
Just right 20.07.2015
I mounted this plate on an old single-barrel Winchester 101 Trap that I recently purchased. Stock had been cut so far back to the point it was midway in the slope of the Monte Carlo. It had also been cut at such a "custom" angle that spacers and a thick pad would not have allowed for a proper fit. The gun was absolutely useless for me although I knew that going in.
I installed one of these along with a T550 Pachmayr Trap Pad. Fitting the plates was tedious with much "cut, grind, and try" but the end result is a great fitting stock. I polished the exposed edges to a shiny finish with a sequence of filing, sanding, and rubbing with 0000 steel wool and "Mother's Aluminum Mag Polish." Due to the Monte Carlo being butchered, I had to lower the pad to what appears to be an excessive amount, but with the adjustments on this plate, I was able to get a perfect fit for me. The option of fitting the plate to the size of the recoil pad rather than fitting the recoil pad to a stock or a spacer has allowed for a greater area for recoil to occur. Might help with felt recoil.
You don't have to be a machinist or an expert gunsmith to install this plate, but basic wood and metal working skills are essential. The fitting of the plates to the stock and recoil pad and the use of a forstner bit near an existing hole takes time and patience.
Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden på nytt for å fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.