EGW recommends measuring the hole spacing in your receiver to confirm it matches with the dimensions they have published. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. EGW machines these in their shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type III anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is sold separately). Recommend: 0 MOA - if shooting 0-500 yards 20 MOA - if shooting 500-1000 yards When zeroing your rifle with a 20 MOA mount, EGW recommends zeroing at 200 yards. The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA. This Mount Fits: Browning BAR (all calibers) Browning BLR Long Action Browning BLR Takedown Browning BPR Browning Short Trac Benelli R1* (see below) This Mount Does Not Fit: Browning BAR MK3 DBM - This rifle has integrated picatinny style rails that are not removable In October 2019 the overall length of this mount was changed from 5.488"" to 5.094"" to accomodate takedown models. If you purchase a mount from a third party seller there is a chance it may be older and not fit your takedown. *This mount will fit the Benelli R1 Rifles. It will cover the middle hole on their action, but will use the front and back pairs. ***This mount does not fit the BAR ShortTrac Hog Stalker. EGW does not have a mount that works with this application. EGW has found that older model BLRs may use the long action rail despite the caliber. Please measure your hole spacing to confirm.
EGW anbefaler å måle avstanden mellom hullene i mottakeren din for å bekrefte at den samsvarer med dimensjonene de har publisert. Picatinny krysspor går over hele lengden av skinnene, noe som gir skytten fleksibilitet når de monterer kikkertsikter og andre tilbehør. Kanalen i midten reduserer den totale massen av monteringen. I mange tilfeller vil den heller ikke hindre bruken av fabrikkens jernsikter. EGW én-dels kikkertsikter er det åpenbare valget for både jegere og taktiske skyttere. EGW maskinerer disse i verkstedet sitt ved hjelp av en av sine maskineringssentra. Etter maskinering blir monteringen vibrert, sandblåst og Type III anodisert for langvarig holdbarhet. Installasjon: EGW anbefaler 20 tommer lbs med dreiemoment og en dråpe blå loctite (loctite selges separat). Anbefaling: 0 MOA - hvis du skyter 0-500 yards 20 MOA - hvis du skyter 500-1000 yards Når du nullstiller riflen din med en 20 MOA montering, anbefaler EGW å nullstille på 200 yards. Hele monteringen og tilbehøret (fra monteringsskruene og verktøyet til emballasjen) er laget i USA. Denne monteringen passer: Browning BAR (alle kalibre) Browning BLR Long Action Browning BLR Takedown Browning BPR Browning Short Trac Benelli R1* (se nedenfor) Denne monteringen passer ikke: Browning BAR MK3 DBM - Denne riflen har integrerte picatinny-stil skinner som ikke kan fjernes. I oktober 2019 ble den totale lengden på denne monteringen endret fra 5.488"" til 5.094"" for å imøtekomme takedown-modeller. Hvis du kjøper en monteringsenhet fra en tredjeparts selger, er det en sjanse for at den kan være eldre og ikke passe til din takedown. *Denne monteringen vil passe til Benelli R1-rifler. Den vil dekke det midterste hullet på deres mekanisme, men vil bruke de fremre og bakre parene. ***Denne monteringen passer ikke til BAR ShortTrac Hog Stalker. EGW har ikke en monteringsenhet som fungerer med denne applikasjonen. EGW har funnet ut at eldre modeller av BLR kan bruke lang aksjonskinne uavhengig av kaliber. Vennligst mål avstanden mellom hullene for å bekrefte.