Pre-formed lead ingot increases the rear weight; balances out muzzle-heavy, match AR-15's for consistent, shot-to-shot accuracy. Denser than loose, lead shot; conveniently drops into the A-2 buttstock and is retained by the trap door. Can be cut, drilled or trimmed to achieve required balance.
Balanserer Geværet For Konsekvent Presisjon
Forhåndsformet blyklump øker bakvekten; balanserer ut fronttunge, match AR-15'er for konsekvent presisjon fra skudd til skudd. Tettere enn løst blyshot; faller enkelt inn i A-2 kolben og holdes på plass av fellen. Kan kuttes, bores eller trimmes for å oppnå ønsket balanse.
Top takeaways
Forhåndsformet blyklump som øker vekten bak og balanserer tunglede, match AR-15 for konsekvent nøyaktighet skudd-til-skudd.
Passer enkelt inn i A-2 kolben og holdes på plass av lukeåpningen, tettere enn løst blyhagl.
Kan kuttes, bores eller trimmes for å oppnå ønsket balanse. Spesifikasjoner: Bly, 8" (20cm) lang, A-2 veier 3 lbs. 11 oz. (1,7kg).
Attributes
Finish:Unfinished
Material:Lead
Våpentype:AR-15
Leveringsvekt:1,656kg
Frakthøyde:18mm
Fraktbredde:74mm
Fraktlengde:302mm
UPC:050806023482
Elementdetaljer
Made in USA
US eksport klassifisering: 0A501.y.1
Kundeanmeldelser
Kundevurderinger (8)
4,6 / 5
Anbefalt med reservasjoner
The good and the not so good 05.07.2018
The good - balances the 20 inch barrel rifle at the magazine well.
The not so good - requires some grinding to get it to fit completely in and not be wedged so tightly that it would be impossible to remove.
Klart anbefalt
Does what I wanted it to 15.09.2017
About as simple a product as you'll likely find; a hunk of lead with a foam pad glued to the end. Mine fit the A2 stock compartment with no trimming required and just a light tap to seat it in. Tap the butt upside down on a hard surface and it comes right out (be careful not to break the door off). I used this to balance a RRA CMP upper with 20 inch heavy barrel which was quite front heavy with the empty stock. Gradually sawed an inch or so at a time off the narrow end until I found the right balance. I ended up needing only about a 1 1/4 inches of the weight. Fits in there snugly and doesn't slide around. Yes, you'll probably have to cut down to the size you need, but no big deal. Just wear latex gloves, be careful with the residue and dispose of properly - this is lead after all. Only con I can think of is that this is a $28 chunk of lead, most of which I now have leftover. Maybe I'll take up bullet casting.
Anbefalt
Not A Drop In 01.05.2017
I ordered this for my 6.5 Grendel AR. It is used exclusively for target shooting from a table. It is equipped with a UTG A2 stock. The weight required extensive material removed to fit the stock. Plan to take an hour or longer to make it fit.
Klart anbefalt
Snug fit 27.07.2015
nice item.. It was a very snug fit in the stock of my Rock River....but only took a few hits with a ball peen hammer to get it to fit...it is NOT coming out.......it added enough weight to the rear of the rifle that it feels balanced to shoot it offhand...HOWEVER I would not want to carry it all over the place....makes the rifle heavy...that is ok...I have some Lightweight Colts and a Carbon Fiber Windham if I want to carry it around.
Klart anbefalt
Great product... 13.03.2014
Put this into a A2 rifle stock, Les Baer, and it fit perfectly. Was a little tight but I slid the stock off and tapped the small end of the stock on the table a couple of times and the lead slid in for a very good fit. This adds over 3lbs of weight to the stock and balances out the weight of the heavy barrel. Makes it very easy to hold the rifle steady in the off hand position. Great product.
Klart anbefalt
Works Great with some modifications. 12.01.2014
While the weight did not fit in my UTG A2 stock easy I still have to give it 5 stars because the mods needed to get it to fit were easy and IMO this is the best possible way to add weight to the stock and balance a ar15 meant for accuracy.
I have a White Oak service upper on a Seekins billet lower and the UTG A2 stock. This weight only dropped into the UTG stock about 90%. Some moderate force with hand got it about 5% more deep and a little hard tapping got it another 1% maybe. But not enough to close trap door even with the end foam piece completely removed. Thankfully the strong foam lined UTG stock kept me from driving it in so tight that I couldn't get the weight back out. The fix after removing it was to cut both ends as only cutting the tapered end would do nothing to get it any deeper into the stock as the large end was preventing the weight from going down any further. I only cut an inch of tampered end to reduce more weight as even my service upper is not heavy enough to need the complete weight of this item. I then cut about 3/4" off the large end as that's the distance I needed to fit weight in far enough to shut trap door with half of the foam piece reattached. Perfect fit, absolutely no movement being I properly measured both distance and weight I needed to both close trap door and balance rifle. I shoot competition service and match so I needed a solid one piece weight that worked. I use to use some .50AE bullets and foam to get them tight in the trap door compartment but this weight just makes it more complete and solid.
I plan to buy at least one more for my old service rifle as these are the only two ar's I own that use A2 stocks. May grab a few more to have different weights for different shooting events.
Klart anbefalt
I would buy this product again and again 01.07.2010
I purchased this product because of hearing good things about it many years ago, and honestly I thought I was throwing my money away on a gimmick. I even thought well the thing probably won't even fit in the cleaning kit well much yet letting the Buttstock trap door close up behind this molded chunk of lead! Well I got this 3lb 11oz molded thing in from UPS so I thought well its here, may as well investigate it. To my surprise this molded trap door weight looked like a very good lead mold, but would it fit? I removed the cleaning kit and slid the weight right in place, it fit perfectly! The end where it would make contact with the trapdoor is a glued on piece of soft foam. There are 3 things this product did for my Colt Match H-Bar, 1.)It made the firearm 3lb 11oz heavier. 2.)It made the firearm more balanced. 3.)Oh and it tightened up my three shot groups by slightly more than .25 of an inch at a hundred yards! The darn thing tightened up my groups! And it fit the Buttstock like a glove! I mean there is just enough room for this weight to fit and the soft foam cussions it against the trap door when it's closed. The only drawback to this is it commits the firearm to strictly a prone/benched Match rifle. That didn't bother me because that's what the heavy rifle was designed for in the first place! I use a Harris 1A2 Bipod for the front and I sandbag the rifle at the rear of this Colt H-Bar Match rifle. My scope is a leopold 4.5 X 14 There is hardly a bit of felt recoil to this "HEAVY" rifle now. I use Winchester 45 GR Factory ammo. I wonder how my groups would be if I did reloads for it? Oh I almost forgot, the twist is 1 x 7" chrome lined barrel, the groups are about an honest 1" three shot groups at 100 yds. I am amazed at what this Buttstock weight has done for my groups! I am very happy I bought this well made product! And I think it is a good price for the tighter groups! It's definately a heavy slug now though. My advice is if you have a Heavy barrel Match A-2 firearm and want to shave a minimum of .25" off your 100 yard groups, get one of these balancing lead weights, it really works! You'll see...
Klart anbefalt
AR-15 A2 Heavy Barrel Match Rifle 01.07.2010
The AR-15 Heavy Barrel "Buttstock Weight" fits my Green Lable AR-15 Heavy Barrel Buttstock cleaning Kit storage Trap Door compartment like a glove! There is just enough room to shut the Trap Door and latch it! I emediately noticed that the rifle was close to being a balanced rifle now. The rifle has always been a prone shooter, but very muzzle heavy and difficult to handle. But now more than ever, it is certainly a prone shooter for sure now. The extra 3+ weight gain of the rifle is very noticable, but it is much closer to being a balanced target shooter. I definately have better/tighter three shot groups benched and sandbagged! The rifle recoil is practically not noticeable at all with the extra weightgain to the extreme rear of the rifle. I am very happy with my purchase. Now the bad news, as I mentioned it is most definately a prone shooter, only a weight lifter could stand and get reasonable groups, I mean it's very heavy! I don't mind I use a Harris 1A2 Bipod in front and sandbag the rear. "It is very stable now!" And as I mentioned I have about a 1 and a quarter inch group now using this "Buttstock Weight" and that is at 100 yards. Sometimes my groups are tighter but never larger than the 1.25" groupings. I'm using Winchester 223 45 GRain JHP rounds 3600 fps ammo. Anyway I've tightened my groups an honest .25" or slightly better, and I think that's worth the investment considering I havent found the rifles best shooting ammo yet. Who knows maybe I can get it down to 1" groups! At a hundred yards I'd be very happy with that! An honest note: "If you don't want to shoot prone don't buy this product."
Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden på nytt for å fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.
Forbedre nøyaktigheten til din AR-15 med BROWNELLS A2 buttstock weight. 🎯 Enkel å tilpasse for perfekt balanse!
Erklæring om kontroll av destinasjon: Disse artiklene er underlagt kontroll av den amerikanske regjering og er kun godkjent for eksport til destinasjonslandet, for anvendelse av den endelige mottager eller sluttbruker(ene), heri identifisert. De skal ikke videreselges, overføres eller på annen måte avhendes til et annet land eller til en annen person enn den godkjente mottakeren eller sluttbrukeren(ene), enten i sin opprinnelige form eller etter innlemmelse i andre artikler, uten først å få godkjenning fra den amerikanske regjering eller dersom godkjennelse følger av amerikanske lover eller forskrifter.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Erklæring om kontroll av destinasjon: Disse artiklene er underlagt kontroll av den amerikanske regjering og er kun godkjent for eksport til destinasjonslandet, for anvendelse av den endelige mottager eller sluttbruker(ene), heri identifisert. De skal ikke videreselges, overføres eller på annen måte avhendes til et annet land eller til en annen person enn den godkjente mottakeren eller sluttbrukeren(ene), enten i sin opprinnelige form eller etter innlemmelse i andre artikler, uten først å få godkjenning fra den amerikanske regjering eller dersom godkjennelse følger av amerikanske lover eller forskrifter.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Praktisk verktøy for fjerning av AR-type forskjefter uten behov for ekstra hender.
Laget av ¼" (6,4 mm) stålstang med syntetisk gummi-belegg for å beskytte våpenet mot riper.
Passer AR-15, M16A1 & A2, og AR-stil .308 rifler med delta-ringer.