Add all the convenience of drop-free, box magazine to your favorite Remington 700 BDL. Spring-loaded finger latch inside the triggerguard drops the box magazine free, speeds loading and unloading. Made from durable stainless steel and finished with bake-on, matte, black Teflon® coating that's self-lubricating and resists scratches and wear. Updated version have positive locking springs on the bottom of both sides of the floor plate (holds the magazine box securely in place without the rubber o-ring), a polymer boot on bottom of box (easier to remove), and a guide slot and larger rear catch on back of box (ensures proper latch).
SPECS: Stainless steel, black, matte finish. 9.3 oz.(265 g) approximate wt. Fits H.S. Precision 2000 and Rem. 700 BDL long and short actions. Will fit Rem. ADL with modifications to stock. May require gunsmithing/fitting. Magazine Capacity – Five rounds with .223, .222 & .204, four rounds with standard calibers, ten rounds available for 308 and similar calibers, three or eight rounds with magnum calibers (8rd magazine holds 7 or 8, depending on cartridge).
Legg til all bekvemmeligheten med drop-free, boks magasin til din favoritt Remington 700 BDL. Fjærbelastet fingerlås inne i avtrekkeren slipper boks magasinet fritt, og gjør inn- og utlasting raskere. Laget av slitesterkt rustfritt stål og ferdig med bake-on, matt, svart Teflon® belegg som er selvsmørende og motstår riper og slitasje. Den oppdaterte versjonen har positive låsesprinter på bunnen av begge sider av gulvplaten (holder magasinboksen sikkert på plass uten gummiring), en polymer boot på bunnen av boksen (enklere å fjerne), og en guide spor og større baklås på baksiden av boksen (sikrer riktig låsing).
SPECS: Rustfritt stål, svart, matt finish. 9.3 oz.(265 g) omtrentlig vekt. Passer H.S. Precision 2000 og Rem. 700 BDL lange og korte handlinger. Vil passe Rem. ADL med modifikasjoner til stokken. Kan kreve gunsmithing/fitting. Magasinkapasitet – Fem skudd med .223, .222 & .204, fire skudd med standard kalibre, ti skudd tilgjengelig for 308 og lignende kalibre, tre eller åtte skudd med magnum kalibre (8rd magasin rommer 7 eller 8, avhengig av patron).
Top takeaways
Legg til et drop-free boksmagasin til din Remington 700 BDL for raskere lasting og lossing.
Rustfritt stål med matt, svart Teflon®-belegg som er selvsmørende og motstandsdyktig mot riper og slitasje.
Oppdatert design med positive låsefjærer, polymerstøvel og føringsspor for sikker og enkel bruk.
Attributes
Finish:Black
Modell:700
Våpentype:Remington
Leveringsvekt:0,204kg
Frakthøyde:33mm
Fraktbredde:119mm
Fraktlengde:150mm
Elementdetaljer
Made in USA
US eksport klassifisering: 0A501.x
Kundeanmeldelser
Kundevurderinger (8)
3,8 / 5
Klart anbefalt
Very good product 09.04.2016
Was very easy to install. Took about 30 mins. Small file and a little time. Fits perfectly. Loads perfectly. Well worth the little time and money.
Anbefalt
Great looking product! 12.08.2015
Did my homework and selected this product for my Rem 700 Sendero based on reviews. When I installed it my first problem was the front action screw now intruded into the action and prevented the bolt from closing. The second issue was the back of the magazine made contact with the lower back bridge of the action and therefore was difficult to install and wouldn't drop from the action when the release was pressed. I installed a .012 shim to correct the problem but then had a problem feeding the last round, (yep, all it takes it .012 to jack it up). I almost sent it back but decided to try removing .015 from the front action screw. The bolt can now close and after testing over three ten round mags I can say it feeds correctly. In defense of HS Precision I seem to always have weird problems when buying and installing stuff like this. I would give it five stars if instructions addressing how to resolve potential problems had been included. I expect it to work as advertised and will repost if I have any major failures. I like that it's a double stack mag and think it's the best looking of all the DBM's on the market.
Klart anbefalt
Works perfectly 12.05.2015
I have this system with 5- and 10-round H-S magazines, fitted into the H-S Precision stock that comes from Remington as part of their Model 5R Milspec. While the system is not drop-in, it is *almost* drop-in. The only conflict is the internal latch that holds onto the magazine. When you release the latch moves outward and this conflicts with the stock crosspiece. I got out a riffler file and made a slim diagonal channel in the soft crosspiece material (no neet to touch the aluminum chassis underneath) and in 10 minutes I had a perfect drop-in fit. On my Manners T5A the same fitment is required, plus a slight enlargement of the rearmost portion of the mag well. Manners will perform this themselves at no cost on a BDL-inlet stock if you ask them at time of purchase.
As to functionality, it is perfect. If your rounds don't fit this magazine then they don't fit any magazine. then they must not conform to 7.62 NATO specs. I have run several types of ammo plus handloads with an OALT of 2.793" and they fit fine. 145gr commercial ammo has a bunch of extra room. 175gr commercial match ammo not so much, but it fits.
Ikke anbefalt
Complete garbage 14.11.2014
I have a H-S precision stock and this bolts in great and that's it. The rest of the product fails in historic proportions. The bullets don't feed at all. The last round never comes out of the magazine cleanly ever! I am extremely disappointed in this product especially for how much it costs and the "reputation" H-S precision has....
Also if you are a precision shooter and think your hand loads will fit. Think again. I had to the shorten the overal length to get the round to fit in the magazine itself. Again I would NEVER RECOMMEND this to anyone.
Anbefalt
Just what I was hoping it would be. 21.05.2014
I purchased this to upgrade my Remington 700 ADL to a Hogue BDL Stock + the Detachable Magazine. First is that with this Hogue stock I had to do some minor filing and fitting. It does not drop in. It is worth the work and not too hard, if you take your time. It is a great fit and improvement over firing one round at a time. Parts quality is the best I've seen. If you are the patient type you will not be disappointed.
Klart anbefalt
Better than I expected! 28.12.2013
This was listed as a drop in kit. But on my Remington 700 bdl, this was not the case. I needed to do a good deal of inletting and relief work to seat this kit properly. No modifying of the kit itself was needed. I used my dremmel tool and slow removal of material until I had a sound fit. Once the main body was seated there were gaps around the edges. I will be using Brownells stainless steel bedding kit to fill these gaps and insure nothing will move about. This kit allows flawless feeding of ammo to battery, and is of better quality than I had anticipated.
Ikke anbefalt
Requires Gunsmithing 30.09.2013
This part required a gunsmith to install on a Remington PSS with the H-S precision stock. Had to opened up with a mill.
The mags will not retain and feed rounds reliably without being tuned. The lips are far too wide apart and are flat, as opposed to curved, which would feed better.
The AI variants are much better products and better quality as well.
Klart anbefalt
Box magazine conversion #1 upgrade !! 29.07.2013
Generation 2 of this product is vastly superior to the original. Less noise, more positive lock, and polymer boot to prevent damage when dropped. Easy to install, no fitting necessary.
Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden på nytt for å fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.
Oppgrader din Remington 700 med dette 10-runders detachable magazine. ✨ Holdbart design og enkel lasting for optimale skyteopplevelser!
Erklæring om kontroll av destinasjon: Disse artiklene er underlagt kontroll av den amerikanske regjering og er kun godkjent for eksport til destinasjonslandet, for anvendelse av den endelige mottager eller sluttbruker(ene), heri identifisert. De skal ikke videreselges, overføres eller på annen måte avhendes til et annet land eller til en annen person enn den godkjente mottakeren eller sluttbrukeren(ene), enten i sin opprinnelige form eller etter innlemmelse i andre artikler, uten først å få godkjenning fra den amerikanske regjering eller dersom godkjennelse følger av amerikanske lover eller forskrifter.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Erklæring om kontroll av destinasjon: Disse artiklene er underlagt kontroll av den amerikanske regjering og er kun godkjent for eksport til destinasjonslandet, for anvendelse av den endelige mottager eller sluttbruker(ene), heri identifisert. De skal ikke videreselges, overføres eller på annen måte avhendes til et annet land eller til en annen person enn den godkjente mottakeren eller sluttbrukeren(ene), enten i sin opprinnelige form eller etter innlemmelse i andre artikler, uten først å få godkjenning fra den amerikanske regjering eller dersom godkjennelse følger av amerikanske lover eller forskrifter.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Socket Head Screw Kit med 168 skruer i 14 forskjellige varianter, inkludert 8 Fillister Head og 6 Weaver Oval Head stiler.
Inkluderer Checker/Shortener Jig for enkel tilpasning av skrue lengde, samt pinsett og diagram for kompatibilitet.
Økonomisk løsning for å ha et bredt utvalg av skruer for baser, ringer, sikter og ribber, produsert i USA.
Ingen behov for spotting scopes eller kikkerter; treff blir umiddelbart synlige med fluorescerende chartreuse-farge.
Praktisk selvklebende bakside som gjør det enkelt å feste målene.
Tilgjengelig i ulike størrelser og pakker, inkludert reparasjonslapper for lengre bruk.
Legg til drop-free, boksmagasin til Remington 700 BDL for rask lasting og lossing.
Holdbart rustfritt stål med selvsmørende, matt svart Teflon® belegg som motstår riper og slitasje.
Passer Remington BDL lange aksjoner, kapasitet på tre runder med standard magnum kammeringer, og aksepterer patroner opptil 3.7" i lengde.
Fullt justerbart avtrekkersett for Remington 700 rifler produsert før 2006, med enkel installasjon og robust aluminiumshus.
Gir mulighet til å justere avtrekksvekt, utkobling og overstyring for optimal skytestil, med en komfortabel avtrekkersko og vertikale riller for godt grep.
Passer til Remington 700, 40X og Model Seven rifler produsert før 2006, med fabrikkens sikkerhetshevarm og boltslipp bevart.
KCIs 26-runds magasin for Glock® 21 dobler ildkraften sammenlignet med standard fabrikk-magasiner, noe som reduserer behovet for hyppige magasinbytter.
Magasinet er laget av polymer og stål, med en herdede kromsilikonfjær som sikrer jevn og pålitelig bevegelse av kulestabelen.
For optimal ytelse kan magasinene trenge flere laste/tømme-sykluser før de aksepterer full 26-runds kapasitet; det anbefales å starte med halv kapasitet og la det stå over natten.
Hjelp og kontakt
Nyhetsbrev
Klassisk visning
Mobilvisning